GRAUPNER Falcon 12 Скачать руководство пользователя страница 29

Страница: 29 / 52

29 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Rudder

Movement of the model

Control surface action (tail view)

Display "Servo limit"

In this menu, the servo travel for all channels can be limited, so that

the servos in gyro mode cannot run to the mechanical stop.

Servo limit setting step-by-step

1. Bring the angle bracket to the desired line.

Moving down the angle bracket beyond the lower edge of the dis-

play will also display additional channels.

2. Push or tap on the ENT key.

Instead of "SEL" on the right edge of the display, "STO" is dis-

played.

3. Now move the servo to be limited in the desired direction and

position.
The corresponding percentage display is displayed inverted.

4. Push or tap on the ENT key.

The displayed value is saved and "SEL" is displayed again instead

of "STO".

5. Follow the same procedure for further limitations.

SERVO LIMIT

2: -150% +150% SEL
3: -150% +150% SEL

4: -150% +150% SEL

1: -150% +150% SEL

5: -150% +150% SEL

6: -150% +150% SEL
7: -150% +150% SEL

SERVO LIMIT

3: -150% +150% SEL

4: -150% +150% SEL

1: -150% +150% SEL

5: -150% +150% SEL

6: -150% +150% SEL
7: -150% +150% SEL

2: -150%

+083%

STO

SERVO LIMIT

3: -150% +150% SEL

4: -150% +150% SEL

1: -150% +150% SEL

5: -150% +150% SEL

6: -150% +150% SEL
7: -150% +150% SEL

2: -150% +083% SEL

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды