GRAUPNER Falcon 12 Скачать руководство пользователя

Страница: 18 / 52

18 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Max. altitude

Not applicable to receiver S1019.AIR and S1035 Falcon 12

In the value field of this line, a maximum height can be specified,

upon reaching which an alarm is triggered. Either in the form of the

"general alarm tone" of the transmitter, a steady beeping in the

rhythm of about one second or the voice output "height".

Note

The height set in the value field of the "Maximum height" line

always refers to the height above the location when the receiver

system is switched on. Actively used, this feature supports the com-

pliance with the various regulations regarding the maximum alti-

tude above ground.

PERIOD

If your system is used exclusively with digital servos, you can set a

cycle time (frame rate) of 10 ms. If using mixed or with the exclusive

use of analogue servos, it is essential to select 20 ms. Otherwise,

analog servos will respond with "trembling" or "growling", even total

failure.

SUMD at channel X

SUMD

SUMDI

S1019.AIR GR-18 HoTT (without vario)

---

S1034 Falcon 12 plus

S1035 Falcon 12

33579 GR-18 HoTT (with vario)

---

33583 GR-24 Pro HoTT

C10

• "No"

The receiver-specific connection is suitable for operating a servo

or comparable RC components.

• "Yes"

If the value field of this line has been set to "yes" and the relevant

receiver is subsequently put into operation again, it permanently

generates a digital sum signal from the control signals of its con-

trol channels and makes this available at the receiver-specific

fixed servo connection. This type of signal was being used by

some of the newest flybarless systems and power supplies.
In conjunction with another HoTT receiver, which has a SUM-

DI(N) input, it can also be used to create a simple or reciprocal

satellite connection, see below.

33583 GR-24 PRO

RECEIVER 2.05

ALARM VOLT:     3.8V
ALARM TEMP:     70°C
Max. altitude:    0m

SUMD at CH8: No

LANGUAGE: English
Ant1 100% Ant2 100%

Period: 20ms

Model type: Airplane

CH10: SERVO

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды