GRAUPNER Falcon 12 Скачать руководство пользователя страница 40

Страница: 40 / 52

40 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Swp cyclic travel 8

Set the "Swp cyclic travel 8" if the menu value is activated so that the

rotor blade located above the tail tube is as accurate as 8° by full roll-

over stroke. To do this, the field must be selected (highlighted field)

so that the swashplate can be controlled and adjusted in direct mode

when gyro gain is switched off. This is the only mode in which the

travel can be set correctly.
It is very important that the travel is set correctly. It plays a major role

in terms of acquiring the correct gyro gain.

Collective_A/B

The display "A" or "B" and its corresponding value changes automat-

ically according to the transmitter-side pitch stick position. The two

endpoints are set separately.
Use the pitch gauge to measure the required pitch travel when the

full commands are applied (±100%) and set it in this menu. All of the

other settings can be made later on the transmitter for the pitch

curves in the respective flying phase.

Adjustment range: +50 … +120

Cyclic max

The swashplate limit must be set so that it is not possible for a servo

to reach its mechanical limits, while ensuring that the servo's travel

is as large as possible. No humming should come from any of the ser-

vos when full travel commands are applied.

Adjustment range: +50 … +200

Swp rotate

In this line, a virtual swashplate rotation can be set in degrees.
Normally for rotor heads with up to a 3 bladed no rotation is neces-

sary.
Adjustment range: ±90

Tail servo

In this line the correct neutral position for the tail servo has to be set.
As a rule, 1.5 ms are not just usual for tail servos. Narrowband ser-

vos (generally special tail rotor servos) may however require a differ-

ent mid pulse width. You must locate this value in the servo manual

and set it correctly. If a value has not been specified, it is probably a

standard servo set at 1.5 ms. For

Graupner

servos of type DES, HVS

or HBS, this value is partially programmable. However, we recom-

mend sticking with the default setting.

Base sett control

Swp direction     +0
Swp Roll trim     +0
Swp Nick trim     +0

Swp cyc. trav 8 +80

Direction right
Swp type 120 degree

Swp Pitch trim +0

Swp frequency 200Hz

Collective A     +80
Cyclic max.      +80
Swp rotate        +0
Tail servo     1,5ms
Tail frequency 333Hz
Tail mid          +0
Tail limit B     +50
4.Swp servo mid   +0
Logging           +3
Expert mode       NO

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Бренды по названию

Популярные бренды