GRAUPNER Falcon 12 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 52

background image

25 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

• Some transmitters allow the corrective factors to be altered

during a flight using the proportional controls, whereas others

allow fixed values only.

• It is possible to use a channel to control the factor value by set-

ting up flight phase specific transmitter control settings, but

only with some transmitters; please see the instructions sup-

plied with your transmitter and refer to the “Transmitter control

settings” and “Flight phase settings”.

Programming example for transmitters with proportional controls

Gyro setting

MODE RU (2)C7

Aile: (2)C9
Elev: (2)C8

MODE AI/EL (2)C7

Rudd: 6

Factor:

(44%)C10

If your HoTT transmitter is equipped with proportional controls, it is

also possible to adjust the value for each axis during a flight: what

you might call ‘flying the settings’. You need to assign proportional

controls to any channel in the range 5 to 16. Now you can alter the

value using these controls. The current value is shown in brackets.

Procedure, using the ailerons as an example step-by-step

1. Assign a free proportional control to a free control channel in the

transmitter's control setup menu.

2. In the transmitter's telemetry menu, switch to the "Gyro setting"

display page of the receiver menus.

3. Move the cursor to the desired line, for example to the "Ailerons"

line for the aileron.

4.  Press the SET key to activate the value field.
5.  Select the channel prepared according to point 1.
6.  Save it by pressing the SET button again.
7.  Move the selected proportional control to check.

If the value displayed in the bracket changes between 0 and 10,

then programming is OK. Otherwise, the relevant settings should

be checked and corrected if necessary.

8. The options "elevator" and "rudder" may have to be set the same.

Notes

• In flight, the values are to be changed successively until the

desired gyro correction is achieved without swinging up.

• Possibly, it makes more sense and the evaluation easier, to acti-

vate first one axis of the gyro and to fly the attitude.

«
...
23
24
25
26
27
...
»

Содержание Falcon 12





















































Отзывы:

Нет отзывов

Похожие инструкции для Falcon 12

Бренд: Ssl Страницы: 16

Бренд: Cables to Go Страницы: 5

Бренд: TANDBERG Страницы: 23

Бренд: Flying Industry Development Страницы: 3

Бренд: Magnadyne Страницы: 48

Бренд: ADI Страницы: 47

Бренд: Blaupunkt Страницы: 17

DEC 664HD/USB/REC

Бренд: Majestic Страницы: 29

Бренд: Trantec Страницы: 22

Бренд: Olin Страницы: 26

Бренд: Outland Technology Страницы: 34

Бренд: Effort International Страницы: 23

Бренд: Jensen Страницы: 100

Бренд: Grandbeing Страницы: 25

BeSpoke Premium Audio pt296-00142

Бренд: Scion Страницы: 189

Бренд: Ublox Страницы: 33

Бренд: Hitachi Страницы: 31

Бренд: Hitachi Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды