GRAUPNER Falcon 12 Скачать руководство пользователя страница 38

Страница: 38 / 52

38 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Display "Base setup control"

Attention

• In the course of the initial setting, the helicopter-specific set-

tings in this menu must be started and this menu must be

worked through from top to bottom point by point.

• As soon as a value is activated in the "Basic setting control"

menu, the gyro control and in some cases also the control is

deactivated! Changes to the settings must therefore never be

carried out in the air, but only when the drive motor is switched

off and on the ground!

Rotating dir

In this line, the direction of rotation of the rotor must be specified.

From the top, clockwise (right) or counterclockwise (left).

clockwise

counter-

clockwise

Swp type

In this line, the "swash plate type" is specified, which is defined by

an angle specification. The appropriate value can usually be found in

the construction manual of the helicopter.

Adjustment range: 4 servos, 90 °, 140 °, 135 ° and 120 °.

Notes

• On the transmitter side it is always set to "1 servo", inde-

pendently of the actual number of swashplate servos.

• The "90 °" setting is only suitable for operating helicopters with

3 swashplate servos in a 90 ° arrangement and a mechanical

pitch mixer.

Base sett control

Swp direction +0

Swp Roll trim +0
Swp Nick trim +0

Swp cyc. trav 8 +80

Direction right
Swp type 120 degree

Swp Pitch trim +0

Swp frequency 200Hz

Collective A +80
Cyclic max. +80
Swp rotate +0
Tail servo 1,5ms
Tail frequency 333Hz

Tail mid +0
Tail limit B +50
4.Swp servo mid +0

Logging +3
Expert mode NO

Содержание Falcon 12





















































Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды

GRAUPNER Falcon 12, Руководство пользователя

Результаты поиска

Содержание Falcon 12

Отзывы:

Похожие инструкции для Falcon 12

Бренды по названию

Популярные бренды