GRASS VALLEY Profile PDR 100 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 78

PDR 100 Fibre Channel Installation

58

PDR 100 Fibre Channel Installation

Installing the Fibre Channel Board

The Fibre Channel board must be installed in slot J15, adjacent to the Master EDR
board. To install the Fibre Channel board, refer to Figure 14 and Figure 15
(page 52) for location, and Figure 18 (page 57) for installation information and
proceed as follows:

1. Slip the Fibre Channel board into the board slide at the front of the board area

for slot J15 aligning it with the edge-board connectors in the motherboard at
the bottom panel and the rear panel cutout for J15.

2. Ensure that the board contacts are correctly aligned with the motherboard

connectors and firmly press down on the board until it is fully seated. Screw
holes in the board bracket should align with the two bracket mounting screw
holes, one on the inside and one on the outside of the rear panel.

3. Use the Torx tool with the T15 bit to secure the Fibre Channel board bracket

to the rear panel with the two screws provided, but do not fully tighten until
after the PCI Interconnect board has been installed.

«
...
56
57
58
59
60
...
»

Содержание Profile PDR 100















































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PDR 100

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Bahco Страницы: 9

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Velp Scientifica Страницы: 12

Бренд: Yamaha Страницы: 24

Бренд: J&M Страницы: 33

Бренд: Rapala Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды