GRASS VALLEY Profile PDR 100 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 78

Reinstalling the Profile Chassis into the Rack

PDR 100 Fibre Channel Installation

71

Reinstalling the Profile Chassis into the Rack

To reinstall the Profile chassis into the equipment rack:

WARNING: Unless the equipment rack is adequately anchored, it could tip
when the Profile chassis is extended on the rack slides. To avoid possible
injury to personnel or damage to the equipment, make sure the rack is firmly
anchored before extending the Profile chassis on the rack slides.

WARNING: The Profile chassis is too heavy for one person to install in an
equipment rack. To avoid possible injury to personnel or damage to the
equipment, get help when re-installing the Profile chassis into the rack.

1. Being sure to fully support the Profile chassis, slide it into the rack slides until

the slide locks engage.

2. Depress the slide locks and slide the Profile chassis completely into the rack.

3. Tighten the retaining screw to secure the Profile chassis in the rack.

Cable Connections

1. If you are using more than two Profile systems, connect the 5 meter Fibre

Channel cable from the Fibre Channel board connector on the rear panel to
the Fibre Channel hub. See the Fibre Channel Hub manual for instructions on
how to install the Fibre Channel Hub.

Note that if connection to the Fibre Channel hub is farther than 25 meters
from the Profile systems, you will need to use fiber-optic cable and the
copper-to-fiber adapter shown in Figure 4, page 22.

For two Profile systems, connect the Fibre Channel cable between the Fibre
Channel board connectors on the rear panels of the Profile chassis.

2. Connect the 5.49 meter Ethernet cable from the LAN connector on the rear

panel to the LAN hub. (See the Ethernet Hub manual for instructions on how
to install the Ethernet Hub.)

3. Re-connect all other previously removed cables.

4. Re-connect the power cord.

5. On the rear panel, press the power switch to

1

(On).

6. On the front panel, press the

STANDBY

switch to

ON

.

«
...
69
70
71
72
73
...
»

Содержание Profile PDR 100















































































Отзывы:

Нет отзывов

Похожие инструкции для Profile PDR 100

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Bacharach Страницы: 48

Бренд: G-Lab Страницы: 16

Бренд: G&G Страницы: 2

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: Kamikaze Страницы: 112

Бренд: KAM Страницы: 2

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: Kärcher Страницы: 20

Бренд: Parker Research Corp Страницы: 3

Бренд: Park House Healthcare Страницы: 32

Бренд: Hoist Fitness Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды