Grant's Automation SD series Скачать руководство пользователя страница 3

Страница: 3 / 34

installation . . . . . . . . . . . . 13

step 1 - install cabling . . . . . . . . . . . . . . . . . . . . . . . 13

tips for running low voltage caBle yourself.

step 2 - Fit the OpeRatOR . . . . . . . . . . . . . . . . . . . . . . 14

position of the operator

check height of the operator

raise the height of the operator if needed

fiX the operator in place

manually release the operator

step 3 - Fit the Rack tO the gate . . . . . . . . . . . . . . . . . . . .17

step 4 - pOweR OpeRatOR up . . . . . . . . . . . . . . . . . . . . . 21

wiring diagram for power connections

checking the gate direction

wiring diagram for the Battery

wiring diagram for a photocell

wiring diagram for digital keypad or press Button

wiring diagram for an intercom

terminating ground loop vehicle detector

terminating a 7-day timer, digital keypad or keyswitch

terminating an intercom

step 5 - mOtOR setup . . . . . . . . . . . . . . . . . . . . . . . . 26

activating remote controls 26

deactivating remote controls 26

setting the gate open and close distance 26

auto-close delay 27

adjusting force setting for safety reverse 27

soft start 27

soft stop 27

motor speed 27

pedestrian gate opening 28

installing the sOlaR panel . . . . . . . . . . . . . . . . . . . . 30

what happens iF theRe is a pOweR cut? . . . . . . . . . . . . . . 31

accessORies . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

tROuble shOOting . . . . . . . . . . . . . . . . . . . . . . . . . . 32

waRRanty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Содержание SD series



































Результаты поиска

Содержание SD series

Отзывы:

Бренды по названию

Популярные бренды

Grant's Automation SD series, Руководство по установке

Результаты поиска

Содержание SD series

Отзывы:

Бренды по названию

Популярные бренды