grandimpianti WF6, Инструкция по установке и эксплуатации

Страница: 17 / 90

17
To select the cycle, open the door by the “P”
button. To change the cycle, with the door
still open, press the “P” button again: the
display will read the corresponding program
number. To confirm the selection just close
the door. Every time the button is pressed
the reading increases by one unit; when the
end of the list is reached the reading starts
from cycle 1 back again.
If the door is open, of course, skip the first
instruction and go straight to cycle selection.
Right after cycle selection, the temperature
display unit will read the maximum
temperature that the cycle will reach for two
seconds; then it will resume normal
temperature reading, i.e the value read by
the probe.
After the cycle has been selected following
the temperature and wash action suggested
by the labels attached to the garments (see
cycle description below), sort the laundry
according to the type of fabric, load the drum
and close the door.
After that, fill the soap bins with detergent
(foam-damping type) according to the cycle
selected. Remember that the bin on the left is
used for pre-wash (if the cycle at issue
includes it), the middle bin is for the main
wash, and the liquid-soap bin on the right is
used for the softener and last-rinse agents.
Then select water level, which ranges
between the factory setting (calculated
following the maximum laundry load) and a
20% reduction that may apply to partial
loads or economy cycles.
This selection is made available by the ad-
hoc button located below the START button.
WARNING! This function simply reduces
the amount of water and soap used with
reference to factory-foreseen amounts. NOT
to be interpreted as "half-load button".
Start the program pressing the green
“START” button, which is on the control
panel, on the right. Then cycle progress will
be shown by the leds on the left of the control
panel (see 7.1).
Pressure on the start button also causes the
timer to commence the countdown to the
end of the cycle (see also function F9 in
paragraph 7.3 CONFIGURATION OF
SETTINGS).
Such time values are those that the
machine has stored in previous equivalent
cycles. Therefore they are not binding but
represent a mere reference.
Each time the push-buttons are pressed the
machine will beep shortly and it will beep
for 15 seconds to anounce that the door is
automatically opened at the end of the cycle.
It is however possible to stop the buzzer by
pressing the ”-” push button or even inhibit
the buzzer altogether through programming
(see 7.3, function F5).
How to change a cycle in progress
If a wrong cycle has been started it is possible
to change the selection within the first two
minutes of operation.
The display showing the cycle number
actually blinks for two minutes after cycle
start, to indicate that it is still possible to
change the selection.
If the "P" button is pressed during this
interval, the cycle is stopped and the next
cycle starts. Again while the cycle display
blinks, it will be possible to switch to the
next selection and so on, until the desired
cycle is reached. Cycle change occurs quickly
after the "P" button is pressed, so that repeated
machine starts and stops are avoided.
Alarm and fault signalling
When faults arise (voltage drop,
overtemperature, water level error) the
washing machine notifies the user by a
number of alarms that appear on the front
panel DISPLAY. All alarm details are dealt
with in the”ALARMS” chapter.
How to correct tub water level reading
Under normal conditions, water level reading
needn’t be corrected, but when special
installation factors like elevation ask for it, it
is possible to set the zero level value in the
tub as follows:
1) Open the door.
2) Check that the tub is empty visually.
3) Hold the “+” and “-” keys down
simultaneously for at least 5 seconds.
4) The DISPLAY will read “CA LI b”
5) Confirm the value read by the card
pressing the PROG push-button.
6) The BUZZER will give out a beep and
the DISPLAYS will return to their
normal functions.
If the water level is corrected, the procedure
has been carried out correctly. Otherwise the
machine will keep the zero value previously
stored
7.2 CYCLE STEPS
The leds on the right part of the control
display indicate the various cycle steps, i.e.
from top to bottom:
1. YELLOW LED: STOP – The wash
cycle is over or the machine has just
been switched on
2. GREEN LED: SOAK – Soak step
underway (when scheduled)
3. GREEN LED: PREWASH – Prewash
step underway (when scheduled)
4. GREEN LED: WASH - Wash step
underway
5. GREEN LED: RINSE 1/RINSE 3 –
Rinse underway (any between 1 and 3)
6. GREEN LED: SPIN – Final or
intermediate spin underway (blinks
when slowing down)
7. GREEN LED: DISTRIB. – Distribution
step underway.
The leds blink when the machine is going
through a transitional intake or drain stage.
The intermittence stops when the machine
has reached the next step.
As soon as the cycle is over the YELLOW
LED goes on and the door is automatically
unlocked: then it will be possible to open the
door and pick the clean laundry.
CAUTION: The door must never be
forced open; use the "P" button or open it
mechanically following the instructions
below.
At any rate, before opening the door make
sure that the drum has stopped, the water has
been drained and the temperature inside the
drum is below 40
°
C (take a look at the
temperature display). Should a potential drop
occur during the wash cycle, it will be
possible to open the door by jerking the
manual puller downwards (see fig. 2).
The device can be reached by a screwdriver
with a small straight bit; insert it in the
appropriate hole located at the bottom of the
machine beneath the lock. First unlock the
door and then open it.
CAUTION: before opening the machine
manually make sure that there is no water in
the tub.
7.3 SETTING PARAMETERS
Besides the “START” and “ECONOMY”
push-buttons, the machine has 4 more buttons
for cycle selection and special functions (see
6.1).
With the door closed, before the cycle is
started, the programming mode can be
entered by pressing the “PROG” push-button.
The time display will then blink “Pr” and the
remaining two displays will go off.
Pressing “PROG” again will cause the display
to read “F1” (on the time display), which stands
for the first function that applies to cycle 1.
www.groupdynamics-laundry.com
sales@groupdynamics.lv