background image

Page 4

Linear Burner Inserts Automated Operation   

Section 2.  General Description 

2.1  Product Overview

This manual provides instructions for installing and replacing the Grand 

Effects

®

 Linear Burner Assembly. 

•  There are two possible mounting locations for the Grand Effects Sub 

Panel: Inner and Outer Mount.

•  Outer Mount means the Sub Panel will be located outside of the burner 

cavity.

•  Inner Mount means the Sub Panel will be located inside of the burner 

cavity.

•  See pictures of system components on Fig.3

•  See schematic of system layouts on Figures 5 and 6.

•  See overview of piping and electrical diagrams on Figures 7,8,9,10.

•  For Outer Mount, Sub Panels require two 4” conduits through cavity 

wall, one for gas and one for electrical.

•  Sub Panels installed as Outer Mounts must be located in a location with 

good drainage.

•  Dimensions to construct burner cavities are shown in Figures 1 and 2.

•  Ventilation is a requirement and must be built into structure as 

shown in Figures 17 and 21.

 WARNING

Improper installation or maintenance can cause nausea or asphyxiation 

from carbon monoxide in flue gases which could result in severe injury, 

or death. For installations that may be close to occupied or living spaces, 

as an additional measure of safety, Zodiac Pool Systems LLC strongly 

recommends the installation of suitable Carbon Monoxide detectors in 

the vicinity of this appliance and in any adjacent occupied spaces.

  WARNING

RISK OF ELECTRICAL SHOCK OR ELECTROCUTION, 

which 

could result in serious injury or death.

 

The Grand Effects Fire Pits 

are only available for 12-volt AC power. For supply connection, use only 

an isolating low voltage power supply with ungrounded output, evaluated 

and listed by a Nationally Recognized Testing Laboratory (NRTL) for 

swimming pool use.

Содержание LIAUT24xxIM





























Отзывы: