background image

Contents 

2

313888E

Contents

Contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

Warnings   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

Product Overview   . . . . . . . . . . . . . . . . . . . . . . . . . .  5

HTX 2030 with Base Coat Pump (257369)  . . . . .  5

Top Coat Pump (Kit 24B140)   . . . . . . . . . . . . . . .  6

Component Identification - Sprayer   . . . . . . . . . . .  7

Component Identification - Base Coat Applicator   8

Component Identification - HTX2030 Air Spray 

Trigger Gun  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  9

Grounding   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10

Pressure Relief Procedure  . . . . . . . . . . . . . . . . . .  10

Applicator (Base Coat Pump)  . . . . . . . . . . . . . .  10

Spray Gun (Top Coat Pump)   . . . . . . . . . . . . . .  11

Start Engine  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

Material and Sprayer Preparation  . . . . . . . . . . .  13

Prime Pump   . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

Spray With Airless Tip . . . . . . . . . . . . . . . . . . . .  14

Spray Without Air - Clear Clog   . . . . . . . . . . . . .  15

Air Assisted Spray 

(Base Coat Applicator)  . . . . . . . . . . . . . . . .  15

Air Assisted Spray 

(Air Spray Trigger Gun)   . . . . . . . . . . . . . . .  16

Spray Gun (Top Coat Pump)   . . . . . . . . . . . . . .  17

Cleanup   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18

Digital Tracking System (DTS)  . . . . . . . . . . . . . . .  21

Main Menu   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21

Secondary Menu - Stored Data Mode   . . . . . . .  22

Digital Display Messages  . . . . . . . . . . . . . . . . . . .  23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  24

Technical Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25

Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  26

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  27

Graco Standard Warranty  . . . . . . . . . . . . . . . . . . .  28

Содержание HTX 2030





























Отзывы: