Graco HTX 2030 Скачать руководство пользователя страница 6

Страница: 6 / 28

Product Overview

313888E

Top Coat Pump (Kit 24B140)

The pump on the HTX 2030 Sprayer can also be
switched out with a Top Coat Kit 24B140

(purchased

separately)

. This pump is used for less viscous

materials such as:

•

Oil-based coatings

•

Enamels

•

Latex

•

Block fillers

•

Elastomerics

•

Epoxies

•

Drywall mud

•

Other high-build materials

For instructions on installing the Top Coat Pump, see
manual 313889.

When Top Coat Pump is Installed

•

Pump will only run when on/off switch is in ON posi-
tion and pump control is rotated clockwise away
from OFF position

•

Pump control setting adjusts sprayer pressure

Rotating knob fully clockwise allows sprayer to

reach maximum working pressure of 3300 psi

(228 bar, 22.8 MPa)

Settings below maximum will lower system

pressure

•

Pump will run whenever system pressure is below
the setting of the pump control

•

Sprayer will not respond to Prime switch or Applica-
tor switch when Top Coat pump is installed

ti13653a

Содержание HTX 2030





























Результаты поиска

Содержание HTX 2030

Отзывы:

Похожие инструкции для HTX 2030

Бренды по названию

Популярные бренды

Graco HTX 2030, Руководство по эксплуатации

Результаты поиска

Содержание HTX 2030

Отзывы:

Похожие инструкции для HTX 2030

Бренды по названию

Популярные бренды