Gorilla Playsets Malibu Pioneer Peak 1500DWR Скачать руководство пользователя страница 98

Страница: 98 / 171

EQUAL

STEP 37: ATTACHING THE FRONT GABLE

ACCOMPLISHED.

2: THE GABLE ASSEMBLY BOTTOM COUNTERSUNK HOLES WILL REMAIN EMPTY FOR NOW.

1: MOUNT THE GABLE ASSEMBLY RESTING ABOVE THE ROPE LADDER SUPPORT, MAKE SURE THE GABLE ASSEMBLY IS

FLUSH AGAINST THE FRONT CORNER POSTS. THE GABLE ROOF PEAK SHOULD BE RESTING ON TOP OF THE ROOF

FRONT SECTION.

TIP: MAKE SURE THE DISTANCE BETWEEN THE GABLE ASSEMBLY AND THE ROOF OVERHANG IS EQUAL ON BOTH SIDES.

IT IS RECOMMENDED TO TEST FIT THE 1 X 4 X 29.29" ROOF FINISHERS FRONT LEFT AND RIGHT TO ASSURE THIS EQUAL

DISTANCE (DO NOT FASTEN). IF NECESSARY SLIDE THE GABLE ASSEMBLY LEFT OR RIGHT UNTIL FINAL POSITION IS

PULL TOWARDS

YOU

FINISHER LEFT

SLIDE LEF

T OR RIGH

FINISHER RIGHT

ROPE LADDER SUPPORT

EMPTY

(TEST FIT ONLY)

ROOF OVERHANG

GABLE ASSEMBLY

1 X 4 X 29.29" ROOF

(TEST FIT ONLY)

EMPTY

1 X 4 X 29.29" ROOF

ROOF

OVERHANG

EQUAL

CORRECT LOCATION.

LEFT TO INSERT THE WOOD SCREWS IN THE

FINISHERS, THESE WILL BE USED IN A LATER STEP.

REMOVE THE ROOF

1-1/2"

WOOD SCREW

3: AFTER THE GABLE ASSEMBLY IS IN ITS FINAL

POSITION. GO INSIDE ON TOP OF THE DECK AND

PULL THE GABLE ASSEMBLY TOWARDS YOU

MAKING SURE IT IS FLUSH TO THE OUTSIDE OF THE

ROOF AND INSERT TWO 1-1/2" WOOD SCREW

FROM UNDERNEATH THE ROOF INTO THE

GABLE ASSEMBLY ROOF PEAK. USE THE

DIMENSIONS SHOWN IN THE DIAGRAM TO THE

NOTE:

CORNER POST

REMOVED FOR

CLARITY

33-7/8"

6 78 "

Содержание Malibu Pioneer Peak 1500DWR












































































































































































Результаты поиска

Содержание Malibu Pioneer Peak 1500DWR

Отзывы:

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Руководство пользователя, Страница: 98 / 171

Результаты поиска

Содержание Malibu Pioneer Peak 1500DWR

Отзывы: