Gorilla Playsets Malibu Pioneer Peak 1500DWR Скачать руководство пользователя страница 100

Страница: 100 / 171

FLUSH

FRONT RIGHT

ROOF FINISHER

1 X 4 X 29.29"

FLUSH

1 X 4 X 29.29"

ROOF FINISHER

FRONT LEFT

5/16" WASHER

DETAIL D

5/16 X 3-1/2" LAG SCREW

STEP 39: ROOF FINISHERS FRONT

1: PLACE THE 1 X 4 X 29.29" ROOF FINISHER FRONT LEFT ANGLED END ON TOP OF THE GABLE ASSEMBLY LEFT SIDE.

PLACE THE 1 X 4 X 29.29" ROOF FINISHER FRONT RIGHT ANGLED END ON TOP OF THE GABLE ASSEMBLY RIGHT SIDE.

FIT THE TONGUE END INTO THE GROOVE OF THE ROOF BOARD ABOVE THEM.

2: MAKE SURE THAT BOTH ROOF FINISHERS ENDS ARE FLUSH ON BOTH SIDES OF THE ROOF AND TIGHT TO THE GABLE

ASSEMBLY.

TIP: DO THIS ONLY IF "THE ROOF FINISHERS ARE UNEVEN WITH THE OVERHANG". REMOVE THE ROOF FINISHERS SO

YOU CAN ACCESS THE WOOD SCREWS ATTACHING THE WALL PANEL SUPPORTS. ONCE YOU REMOVED THE WALL

PANEL SUPPORTS ON BOTH SIDES, PROCEED TO LOOSEN UP THE WOOD SCREWS ATTACHING THE GABLE ASSEMBLY

FROM UNDERNEATH THE ROOF. SLIDE THE GABLE ASSEMBLY LEFT OR RIGHT. TEST FIT THE ROOF FINISHERS ON BOTH

SIDES. ONCE THE CORRECT POSITION IS ACCOMPLISHED PROCEED TO RE-ATTACH THE REMOVED PIECES.

3: INSERT 5/16 X 3-1/2" LAG SCREWS AND 5/16" WASHERS INTO THE WALL PANEL SUPPORTS AND GABLE ASSEMBLY

COUNTERSUNK HOLES.

4: FASTEN THE ROOF FINISHER FRONT LEFT AND ROOF FINISHER FRONT RIGHT TO THE ROOF SUPPORTS AND TO THE

WALL PANEL SUPPORTS WITH #8 X 1-1/2" WOOD SCREWS ON BOTH SIDES OF THE ROOF.

WALL PANEL SUPPORT LEFT

1-1/2" WOOD SCREW

ROOF FINISHER FRONT LEFT

1-1/2" WOOD SCREW

5/16" WASHER

DETAIL C

ROOF BOARD

1 X 4 X 29.29"

5/16 X 3-1/2" LAG SCREW

Содержание Malibu Pioneer Peak 1500DWR












































































































































































Результаты поиска

Содержание Malibu Pioneer Peak 1500DWR

Отзывы:

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Руководство пользователя, Страница: 100 / 171

Результаты поиска

Содержание Malibu Pioneer Peak 1500DWR

Отзывы: