Gorilla Playsets Malibu Pioneer Peak 1500DWR Скачать руководство пользователя страница 8

Страница: 8 / 171

IMPORTANT DOCUMENTS

CUSTOMER MUST READ AND RETAIN

Please go to the following links and read important SAFETY information prior

to using your new play structure.

http://www.gorillaplaysets.com/Swing-Set-Safety-s/85.htm

https://www.gorillaplaysets.com/Maintenance-s/129.htm

http://www.gorillaplaysets.com/manuals.html

(Click on your specific model)

http://www.gorillaplaysets.com/Warranty-s/82.htm

NOTE:

Your children’s safety is our #1 concern. Observing the following statements

and warnings reduces the likelihood of serious injury. Please review these safety rules

regularly with your children.

WARNING:

Children must NOT use this play set until it has been

completely assembled and inspected by an adult to

ensure it has been properly installed.

Gorilla Playsets

190 Etowah Industrial Court

Canton, GA. 30114

Содержание Malibu Pioneer Peak 1500DWR












































































































































































Результаты поиска

Содержание Malibu Pioneer Peak 1500DWR

Отзывы:

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Руководство пользователя, Страница: 8 / 171

Результаты поиска

Содержание Malibu Pioneer Peak 1500DWR

Отзывы: