manualshive.com logo in svg

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Руководство пользователя, Страница: 117 / 171

Поделиться
Скачать
Gorilla Playsets Malibu Pioneer Peak 1500DWR Скачать руководство пользователя страница 117

MARKS OR TAPE.  TIE THREE KNOTS UNDER THE ROPE 

5) SLIDE THE NEXT ROPE LADDER RUNG UP TO THE 

ROPE LADDER SUPPORT

2) MEASURE DOWN 6" BELOW THE BOTTOM OF THE ROPE 

ROPE LADDER RUNNER

KNOT SHOULD BE 6" BELOW THE ROPE LADDER SUPPORT.

1) TIE A KNOT IN EACH ROPE AND THREAD THEM 

LADDER RUNG.

6) REPEAT 4 & 5 FOR REMAINING ROPE LADDER RUNGS.

3) TIE THESE THREE KNOTS BELOW THE ROPE LADDER RUNG.

THE ROPE OR MARK WITH A PEN.

LADDER SUPPORT AND TIE 3 KNOTS.  THE BOTTOM OF EACH 

THROUGH THE BACK SIDE OF THE ROPE LADDER SUPPORT.

2.1) SLIDE A ROPE LADDER RUNG AGAINST THE THREE KNOTS.

4) MEASURE DOWN 10-5/8" BELOW THE 

ROPE LADDER RUNG AND PLACE TAPE ON 

7) TIE KNOTS ON BACK SIDE OF ROPE LADDER RUNNER.

THIS IS THE VIEW AS IF YOU WERE STANDING AT THE FRONT - RIGHT OF THE PLAY SET

 6" 

 10 58 " 

1:  FIND THREE ROPE LADDER ROPES.  MAKE A KNOT IN THE END OF EACH ROPE AND THREAD THE FREE END THROUGH THE 

BACK SIDE OF THE ROPE LADDER SUPPORT.  PULL EACH ROPE TAUGHT.

2: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER SUPPORT 6 INCHES AND TIE A KNOT.  THE BOTTOM OF THE KNOT 

SHOULD BE 6 INCHES BELOW THE ROPE LADDER SUPPORT.  SLIDE EACH ROPE THROUGH THE HOLES IN ONE ROPE LADDER 

RUNG.  SLIDE THE RUNG UP AGAINST THE BOTTOM OF THE KNOTS.

3: TIE THREE KNOTS BELOW THE ROPE LADDER RUNG.

4: MEASURE DOWN FROM THE BOTTOM OF THE ROPE LADDER RUNG 10-5/8 INCHES AND MAKE A MARK ON THE ROPE WITH A 

PIECE OF TAPE OR A MARKER.  THREAD ANOTHER ROPE LADDER RUNG ONTO THE ROPES.

5: WITH THE TOP OF THE RUNG EVEN WITH THE 10-5/8" MARK TIE THREE KNOTS BELOW THE SECOND ROPE LADDER RUNG.

6: REPEAT SUBSTEPS 4-5 FOR THE REMAINING ROPE LADDER RUNGS.

7: THREAD THE BOTTOM END OF EACH ROPE THROUGH THE HOLES IN THE ROPE LADDER RUNNER AND TIE THEM OFF.  GRAB 

EACH ROPE AND ATTEMPT TO WRAP IT AROUND YOUR HAND.  IF THE ROPE WRAPS AROUND YOUR HAND IT IS TOO LOOSE.  IF 

THE ROPE IS TOO LOOSE UNTIE THE KNOT BEHIND THE ROPE LADDER RUNNER AND RETIE IT UNTIL YOU CAN NO LONGER WRAP 

THE ROPE AROUND YOUR HAND.

STEP 56: ROPE LADDER

109

Содержание Malibu Pioneer Peak 1500DWR












































































































































































Отзывы:

Нет отзывов