manualshive.com logo in svg

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Руководство пользователя, Страница: 96 / 171

Поделиться
Скачать
Gorilla Playsets Malibu Pioneer Peak 1500DWR Скачать руководство пользователя страница 96

4: INSTALL TWO 2" WOOD SCREWS FROM UNDERNEATH THE ROOF INTO THE DORMER MOUNTING BLOCKS.

3: REPEAT SUB-STEPS 1 TO 2 FOR THE OTHER DORMER.

2" WOOD SCREW

STEP 35:  DORMERS 

1: USE THE INSTRUCTIONS PROVIDED IN THE APPENDIX TO BUILD THE DORMERS. AFTER INSTALLING THE SEVENTH 

ROOF BOARD INSTALL THE DORMER MOUNTING BLOCK 9-3/4" FROM THE SIDE EDGE OF THE ROOF TO THE SIDE 

EDGE OF THE DORMER MOUNTING BLOCK, AND 15" FROM THE BOTTOM OF THE SEVENTH ROOF BOARD TO THE TOP 

EDGE OF THE DORMER MOUNTING BLOCK. INSERT TWO #8 X 2" WOOD SCREWS THROUGH THE MOUNTING BLOCK 

INTO THE ROOF BOARD.
2: MOUNT THE DORMER ON TOP OF THE ROOF, 4-1/2" FROM THE BOTTOM EDGE OF THE SEVENTH ROOF BOARD TO 

THE BOTTOM EDGE OF THE DORMER, THE DORMER MOUNTING BLOCK SHOULD BE IN BETWEEN THE WALLS OF THE 

DORMER. MAKE SURE THE DORMER IS HORIZONTALLY PARALLEL TO THE ROOF BOARDS AND FULLY RESTING ON TOP 

OF THE ROOF. THE PRE-DRILLED HOLES ON EACH SIDE OF THE DORMER SHOULD BE CENTERED WITH THE DORMER 

MOUNTING BLOCK. INSERT ONE #8 X 2-1/2" WOOD SCREW THROUGH EACH HOLE ON BOTH SIDES INTO THE 

DORMER MOUNTING BLOCK.

DORMER MOUNTING BLOCK

DORMER

2-1/2" WOOD SCREW

SEVENTH ROOF BOARD

1 " 

2

 4

 9 34 " 

 15" 

88

Содержание Malibu Pioneer Peak 1500DWR












































































































































































Отзывы:

Нет отзывов