Gorilla Playsets 1500IWF Скачать руководство пользователя страница 180

Страница: 180 / 205

1) Center the mesh on the inside of the lower clatter bridge rail. The top of the mesh border should be flush to

(06-2004) Clatter Bridge Mesh Panels

**FOR AGES 3-11**

CENTER THE MESH PANEL ON THE CLATTER BRIDGE RAIL ON THE INSIDE.

the top of the clatter bridge rail. If you wish you may mark through the center of the grommets and then drill a

GROMMETS

1/8" pilot hole by 1" deep before installing the pan head screws.

panels but they are solely for the purposes of demonstrating how the mesh should be installed.

AT END OF

MESH.

grommet. Repeat this process for all the grommets across the top of the mesh.

3) Go to each end of the mesh. Push the end of the mesh tight to the corner post or clatter bridge post. Then

install screws and washers into the two grommets on each end of the mesh.

4) Repeat substeps 1 through 3 for the mesh panel on the lower bridge rail on the opposite side.

2) The "recessed area" in the grommet will receive the washer. Place a pan head screw through a washer.

TWO

**FOR RESIDENTIAL USE ONLY**

NOTE THE GROMMETS HAVE A RECESSED PART ON ONE SIDE AN IT SHOULD FACE YOU.

YOU MAY PRE-DRILL 1/8" X 1" DEEP HOLES AT EACH GROMMET LOCATION ALONG THE TOP

PRIOR TO INSTALLING THE PAN HEAD SCREWS AND WASHERS PROVIDED.

Place the screw centered through the grommet and drive it in. The washer should seat centered with the

Note: Your mesh panels will be completely green. The pictures below show white border and black mesh

Tools Required:

#2 Phillips Bit or screwdriver

1/8" drill bit

Pencil

Drill

**IMPORTANT** - Teach your children not to climb onto or hang from the mesh panels.

If the mesh ever becomes ripped please replace the damaged panel(s).

Kit Contents:

2 - Green Mesh Panels 66" x 24"

44 - Phillips Pan Head Screws

5.5mm x 25.4mm long

44 - Washers 16mm O.D. X 7.1mm I.D.

Содержание 1500IWF














































































































































































































Результаты поиска

Содержание 1500IWF

Отзывы:

Похожие инструкции для 1500IWF

Бренды по названию

Популярные бренды

Gorilla Playsets 1500IWF, Руководство пользователя

Результаты поиска

Содержание 1500IWF

Отзывы:

Похожие инструкции для 1500IWF

Бренды по названию

Популярные бренды