Gorilla Playsets 1500IWF Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 205

background image

WITH 3/8" WASHER

3/8" X 5" LAG SCREW

WITH 5/16" WASHER (BOTH SIDES)

5/16" X 3-1/2" LAG SCREW

ENDS FLUSH TO

FRONT FACE OF POST

CENTER DECK SUPPORT

ASSEMBLY

(CENTER IT BETWEEN THE

REAR CORNER POSTS.)

LEVEL WITH EACH OTHER

FLUSH

STEP 27: CENTER DECK SUPPORT ASSEMBLY

INSTALLATION AND LAGS

1: PLACE THE CENTER DECK SUPPORT ASSEMBLY ON TOP OF THE 4 X 4 X 70" UPPER LEVEL UNDER DECK

SUPPORT. THE 4 X 4 X 59-1/2" LOWER LEVEL CENTER POST SHOULD FIT INSIDE THE CENTER DECK SUPPORT

ASSEMBLY.
2: MAKE THE CENTER DECK SUPPORT ASSEMBLY LEVEL WITH THE UPPER LEVEL DECK SUPPORTS. THE END OF

THE CENTER DECK SUPPORT ASSEMBLY SHOULD BE FLUSH TO THE SIDE OF THE LOWER LEVEL CENTER POST.
3: ATTACH THE CENTER DECK SUPPORT ASSEMBLY TO THE 4 X 4 X 59-1/2" LOWER LEVEL CENTER POST WITH

5/16" X 3-1/2" LAG SCREWS AND 5/16" WASHERS.
4: CENTER THE CENTER DECK SUPPORT ASSEMBLY ON TOP OF THE 4 X 4 X 70" UPPER LEVEL UNDER DECK

SUPPORT. LEAVE AN EQUAL SPACE ON EACH SIDE OF THE CENTER DECK SUPPORT ASSEMBLY. THE END OF

THE CENTER DECK SUPPORT ASSEMBLY SHOULD BE FLUSH TO THE OUTSIDE OF THE REAR CORNER POSTS.
5: FASTEN THE CENTER DECK SUPPORT ASSEMBLY TO THE 4 X 4 X 70 UPPER LEVEL UNDER DECK SUPPORT

WITH A 3/8" X 5" LAG SCREW AND A 3/8" WASHER.
6: FASTEN THE BOTTOM HOLES OF THE SIDE SANDBOX BOARDS/REAR SANDBOX BOARD TO THE REAR

CORNER POSTS WITH 5/16" X 3-1/2" LAG SCREWS AND 5/16" WASHERS.

5/16" WASHER

5/16" X 3-1/2" LAG SCREW AND

SIDE SANDBOX BOARDS

AND REAR SANDBOX

BOARD LAGS.

76

«
...
84
85
86
87
88
...
»

Содержание 1500IWF














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1500IWF

Бренд: Quivogne Страницы: 13

Бренд: Sagola Страницы: 62

Бренд: Vaisala Страницы: 60

Бренд: Zero 88 Страницы: 22

Бренд: Ugin Страницы: 39

Бренд: Numark Страницы: 11

AKKU BEK-10 Kaleidoscope

Бренд: EuroLite Страницы: 16

Бренд: HABYS Страницы: 20

ULTRA-VEYOR SYSTEM

Бренд: Walinga Страницы: 56

Бренд: Quadro Страницы: 20

Бренд: paladin Страницы: 35

Riceter fg Series

Бренд: Kett Страницы: 28

Wooden Swing Set Factory

Бренд: Tree Frogs Страницы: 48

MACHINE CONTROL AG System Five

Бренд: Topcon Страницы: 112

Бренд: National Instruments Страницы: 26

Бренд: Beta Страницы: 12

Бренд: Robert Juliat Страницы: 48

Бренд: Aksoz Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды