manualshive.com logo in svg

Gorilla Playsets 1500IWF, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets 1500IWF Скачать руководство пользователя страница 83

4-1/2"

HEX BOLT

SANDBOX

5/16" 

HEX BOLT

WASHER

UPPER LEVEL STEPS/RAILING BOARD

(3 HOLES ON CENTER)

LAG SCREW

UNDER DECK SUPPORT

3/8" X 5"

4 X 4 X 70" UPPER LEVEL

2 X 4 X 70" 

(OFFSET UP)

5/16" WASHER

BOARD

4-1/2"

5/16" X 

2 X 6 X 70"

5/16" X 

3/8" 

WASHER

LAG

POST

T-NUT

STEP 24: UPPER LEVEL - RAILING & UNDER DECK SUPPORT

1: PLACE THE 2 X 4 X 70" UPPER LEVEL STEPS/RAILING BOARD (3 HOLES ON CENTER) AT THE TOP OF THE 

REAR CORNER POSTS.  THIS BOARD WILL GET ATTACHED TO THE 2ND HOLE DOWN FROM THE TOP OF THE 

POSTS.  THE T-NUT FOR THIS BOARD SHOULD BE ON THE INSIDE OF EACH POST ALREADY.  FASTEN THE UPPER 

LEVEL RAILING BOARD TO THE REAR CORNER POSTS WITH 5/16" X 4-1/2" HEX BOLTS AND 5/16" WASHERS.
2: PLACE THE 2 X 6 X 70" SANDBOX BOARD (OFFSET UP) AT THE BOTTOM OF THE REAR CORNER POSTS.  

FASTEN THE TOP HOLES IN THE SANDBOX BOARD TO THE REAR CORNER POSTS WITH 5/16" X 4-1/2" HEX 

BOLTS AND 5/16" WASHERS.
3: PLACE THE 4 X 4 X 70" UPPER LEVEL UNDER DECK SUPPORT DIRECTLY UNDERNEATH THE UPPER LEVEL 

DECK SUPPORTS.  ATTACH THE UNDER DECK SUPPORT TO THE REAR CORNER POSTS WITH 3/8" X 5" LAG 

SCREWS AND 3/8" WASHERS.
4: HAMMER A T-NUT INTO THE HOLE IN THE LAG POST ON THE RIGHT SIDE OF THE FORT.

73

Содержание 1500IWF














































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды