manualshive.com logo in svg

Gorilla Playsets 1500IWF, Руководство пользователя

Поделиться
Скачать
Gorilla Playsets 1500IWF Скачать руководство пользователя страница 90

STEP 31: SIDE REAR ANGLE SUPPORTS

1: (SEE DETAIL A) PLACE THE 2 X 4 X 18" ANGLE SUPPORT UPPER LEVEL RAD RIDE SIDE UNDER THE 4 X 4 X 23-

1/2" SLIDE BLOCK ON THE LEFT SIDE OF THE FORT.  THE ANGLE SUPPORT SHOULD BE FLUSH TO THE LEFT SIDE 

OF THE LEFT REAR CORNER POST.  ATTACH THE ANGLE SUPPORT AT THE TOP AND AT THE BOTTOM WITH ONE 

#8 X 2" WOOD SCREW AND ONE #8 X 3" WOOD SCREW.  
2: (SEE DETAIL B) PLACE THE 2 X 4 X 21-1/2" ANGLE SUPPORT UPPER LEVEL SWING SIDE AGAINST THE 2 X 4 X 

34" UPPER LEVEL DECK SUPPORT ON THE RIGHT SIDE OF THE FORT.  THE TOP OF THE ANGLE SUPPORT 

SHOULD BE FLUSH TO THE TOP OF THE DECK SUPPORT.  FASTEN THE TOP OF THE ANGLE SUPPORT TO THE 

DECK SUPPORT WITH FOUR #8 X 2-1/2" WOOD SCREWS.  FASTEN THE BOTTOM OF THE ANGLE SUPPORT TO 

THE RIGHT REAR CORNER POST WITH ONE #8 X 2" WOOD SCREW AND ONE #8 X 3" WOOD SCREW.

LEFT SIDE OF FORT

A

#8 X 2" WOOD SCREW

#8 X 2" WOOD SCREW

#8 X 3" WOOD SCREW

DETAIL A 

SCALE 1 : 14

RAD RIDE SIDE

2 X 4 X 18"

ANGLE SUPPORT

UPPER LEVEL

#8 X 3" WOOD SCREW

SLIDE

BLOCK

RIGHT SIDE

OF FORT

B

#8 X 3" WOOD SCREW

DETAIL B 

SWING SIDE

#8 X 2" WOOD SCREW

SCALE 1 : 12

2 X 4 X 21-1/2"

ANGLE SUPPORT

UPPER LEVEL

#8 X 2-1/2" WOOD SCREW (4)

DECK SUPPORT

TOPS FLUSH

80

Содержание 1500IWF














































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды