Gorilla Playsets 1500IWF Скачать руководство пользователя страница 160

Страница: 160 / 205

DECK SUPPORT

FRONT FACE BOARD

QUICK LINK

NOTE: TO ACHIEVE THE CORRECT

GAP YOU MAY NOT BE

CONNECTING THE END LINK OF

EACH CHAIN. FOR EXAMPLE YOU

MAY HAVE TO CONNECT THE

SECOND, THIRD, FOURTH LINKS,

ETC. TOGETHER.

CHAIN MUST GO THROUGH

TWO BOARDS

NO EXCEPTIONS!!

STEP 20: BRIDGE DECK/CHAIN INSTALLATION

1: TWO PEOPLE MAY BE REQUIRED FOR THIS STEP.
2: THERE SHOULD BE AT LEAST A 1" TO 1-3/4" GAP BETWEEN THE BRIDGE DECK BOARD AND THE FRONT FACE

BOARD ON THE PLAY SET. THIS MEANS THAT YOU WILL HAVE TO CONNECT THE ENDS OF THE CHAINS

IN A MANNER TO ACHIEVE THE CORRECT GAP. IN ORDER TO ACHIEVE THE GAP YOUR ASSISTANT MAY

HAVE TO LIFT UP THE BRIDGE DECK ASSEMBLY WHILE YOU CONNECT THE CHAINS TOGETHER WITH THE

QUICK LINK UNDER THE PLAY SET DECK. IF YOU HAVE LOOSE ENDS OF THE CHAINS HANGING DOWN

THREAD THEM THROUGH THE QUICK LINK TO KEEP THEM UP AND OUT OF THE WAY.
3: THREAD THE CHAIN ENDS IN THE BRIDGE DECK ASSEMBLY THROUGH THE HOLES IN THE FRONT FACE

BOARD AT THE FRONT OF THE PLAY SET. THEN THREAD EACH CHAIN THROUGH THE HOLES IN THE DECK

SUPPORT. CONNECT THE LEFT CHAIN TO THE RIGHT CHAIN WITH A QUICK LINK.

1" to 1-3/4"

150

Содержание 1500IWF














































































































































































































Результаты поиска

Содержание 1500IWF

Отзывы:

Похожие инструкции для 1500IWF

Бренды по названию

Популярные бренды

Gorilla Playsets 1500IWF, Руководство пользователя

Результаты поиска

Содержание 1500IWF

Отзывы:

Похожие инструкции для 1500IWF

Бренды по названию

Популярные бренды