background image

3

SHIPPING INSPECTION

Checking Product Received

Upon receiving the unit, inspect it for damage from shipment. Claims for damage, either shipping or concealed, should be
filed immediately with the shipping company. Check the unit model number, specifications, electrical characteristics and
accessories to determine if they are correct. In the event an incorrect unit is shipped, it must be returned to the supplier
and must NOT be installed. The manufacturer assumes no responsibility for installation of incorrectly shipped units.

MESSAGE TO THE HOMEOWNER

These instructions are addressed primarily to the installer; however, useful maintenance information is included and
should be kept, after installation, for future reference.

REPLACEMENT PARTS

Ordering Parts

When reporting shortages or damages, or ordering repair parts, give the complete unit model and serial numbers as
stamped on the unit’s nameplate. Replacement parts for this appliance are available through your contractor or local
distributor. For the location of your nearest distributor, consult the white business pages, the yellow page section of the
local telephone book or contact:

CONSUMER AFFAIRS

GOODMAN MANUFACTURING COMPANY, L.P.

7401 SECURITY WAY

HOUSTON, TEXAS 77040

877-254-4729

IMPORTANT SAFETY INSTRUCTIONS

Recognize Safety Symbols, Words, and Labels

The following symbols and labels are used throughout this
manual to indicate immediate or potential hazards. It is the
owner’s responsibility to read and comply with all safety
information and instructions accompanying these symbols.
Failure to heed safety information increases the risk of serious
personal injury or death, property damage and/or product
damage.

WARNING

T

O AVOID  PROPERTY DAMAGE, PERSONAL INJURY  OR DEATH, DO  NOT USE

THIS  UNIT IF  ANY  PART HAS BEEN UNDER  WATER. 

I

MMEDIATELY CALL A

QUALIFIED SERVICE  TECHNICIAN  TO INSPECT THE FURNACE  AND  TO REPLACE

ANY PART OF THE CONTROL SYSTEM AND ANY GAS CONTROL HAVING BEEN

UNDER WATER.

WARNING

T

HIS UNIT MUST NOT  BE USED  AS A  "CONSTRUCTION HEATER" DURING  THE

FINISHING PHASES OF CONSTRUCTION ON A NEW STRUCTURE.  

T

HIS TYPE OF

USE MAY RESULT IN  PREMATURE FAILURE OF THE UNIT DUE TO EXTREMELY

LOW RETURN AIR TEMPERATURES AND EXPOSURE TO CORROSIVE OR  VERY

DIRTY ATMOSPHERES.

WARNING

D

O NOT CONNECT  TO OR USE  ANY DEVICE THAT IS NOT DESIGN-CERTIFIED

BY 

G

OODMAN FOR USE WITH THIS UNIT. 

S

ERIOUS PROPERTY DAMAGE,

PERSONAL INJURY, REDUCED UNIT PERFORMANCE AND/

OR

 HAZARDOUS

CONDITIONS MAY RESULT FROM THE USE  OF SUCH NON-APPROVED DEVICES.

WARNING

HIGH

 

VOLTAGE

!

D

ISCONNECT 

ALL

 POWER BEFORE SERVICING OR INSTALLING

THIS UNIT. 

M

ULTIPLE POWER SOURCES MAY BE PRESENT. FAILUR

TO DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR

DEATH.

E

WARNING

C

ONNECTING UNIT DUCT WORK TO UNAUTHORIZED HEAT PRODUCING DEVICES

SUCH AS A FIREPLACE INSERT, STOVE, ETC. MAY  RESULT IN PROPERTY

DAMAGE, FIRE, CARBON MONOXIDE POISONING, EXPLOSION, PERSONAL

INJURY OR DEATH.

WARNING

T

HIS PRODUCT CONTAINS OR PRODUCES A CHEMICAL OR CHEMICALS WHICH

MAY CAUSE SERIOUS ILLNESS  OR DEATH AND WHICH ARE KNOWN TO THE

S

TATE OF 

C

ALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

 

WARNING

T

O PREVENT  THE RISK  OF PROPERTY DAMAGE,  PERSONAL INJURY, OR  DEATH,

DO NOT STORE  COMBUSTIBLE MATERIALS OR USE GASOLINE OR  OTHER

FLAMMABLE LIQUIDS OR VAPORS IN THE VICINITY OF THIS APPLIANCE.

Содержание GPC15 SEER





















Отзывы: