Goldacres Prairie Compact 400L Скачать руководство пользователя страница 5

Страница: 5 / 44

• Never attempt to clean parts, or nozzles, by

blowing with mouth.

• Never attempt to siphon chemicals, or

substances, by sucking.

• It is imperative that the tow vehicle

manufacturer’s specifications be

checked and all instructions for use when

transporting, or towing, be adhered to at all

times.

• Care should be taken when transferring

liquid into the tank to ensure that the gross

weight of the trailer does not exceed the

braking and carrying capacity as specified

by the tow vehicle manufacturer.

NOTE: 1 Litre water = 1 Kg.
• Water weighs 1kg per litre, however

conversion factors must be used when

spraying liquids that are heavier or lighter

than water. Example: liquid nitrogen has a

density of 1.28 kg/L and will therefore be

significantly heavier than water if the tank is

filled completely. The total weight of a tank

full of chemical, should not exceed that of

a full tank of water. Machine damage can

result if the machine is over weight. See

filling instructions in Chapter 8 ‘Operation’

for more information.

• Consideration should be given to both

the carrying capacity of the trailer and the

gradient of the terrain when determining

the speed at which the tow vehicle can be

driven safely.

• Ensure equipment is securely fastened or

attached to machine at all times.

• Never stand within the radius of the boom

wings.

Cautions

• A supply of fresh water should be with the

equipment at all times.

• Water tanks are not designed for use with

diesel fuel or any flammable liquid.

• Do not use this machine in ambient

temperatures exceeding 40 degrees

Celsius.

• Ensure that all bolts are tightened and

secured before operation.

• Always ensure that the boom is securely

supported when travelling.

• Where fitted, care should be taken to never

overfill the diaphragm pump with oil or

operate at speeds exceeding 540 rpm.

• Do not exceed the maximum spraying

pressure of 8 Bar.

Dangers

•

Check area to be sprayed for overhead

powerlines. Contact between the machine

and powerlines can result in serious injury

or death.

Personal Protective Equipment (PPE)

Always wear close fitting clothing and

appropriate safety equipment designed for

the job at hand.
• Exposure to loud noise over an extended

period can cause permanent hearing

impairment or loss. Be active in the

conservation of your hearing and wear

appropriate hearing protection at all

times.

• Chemicals can be harmful to humans,

appropriate PPE should be used when

handling chemicals.

CAUTION: Always refer to the chemical

manufacturers label for guidelines on the

appropriate PPE to use with the chemical/s

you are using.
Goldacres also suggests that you read

and understand the following Australian

standards:
• Australian Standard for Chemical

protective clothing AS3765.

• Australian Standard for Respiratory

protection devices AS1715.

Poisons Information Centres - Call 131 126

(AU)

Cuts, Stabs & Punctures

When Servicing machine, be mindful of sharp

edges on parts such as trimmed cable ties,

hose clamps, cut reinforced hose and the

edges of plates and brackets as they could

cause cut, stab or puncture injuries.

Crush Hazard

Never attempt to maintain axles, wheels or

components within the vicinity of the wheels

with the tow vehicle running or in motion.

Pinch Hazard

When operating moving components such as

the boom or other components, keep fingers

and hands away from potential pinch points.

Continued over page

Содержание Prairie Compact 400L













































Результаты поиска

Содержание Prairie Compact 400L

Отзывы:

Похожие инструкции для Prairie Compact 400L

Бренды по названию

Популярные бренды

Goldacres Prairie Compact 400L, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание Prairie Compact 400L

Отзывы:

Похожие инструкции для Prairie Compact 400L

Бренды по названию

Популярные бренды