background image

 

 

Macho Pop

 

Model No. 2553 Series and 2554 Series 

 

Page 7 

 

 

gmpopcorn.com 

 

OPERATING INSTRUCTIONS 

Controls and Their Functions 

LIGHTS/WARMER SWITCH 

Two position (ON/OFF), lighted rocker switch(s) which operates the interior light, dome 

light, and heat element for the corn deck freshener. 

KETTLE MOTOR SWITCH 

Two position (ON/OFF), lighted rocker switch which operates the kettle agitator motor, 

and the exhaust fan. The Kettle Motor Switch MUST be ON at all times when there is 

popcorn (popped or un-popped) in the kettle. When finished popping, the unit should be 
sufficiently vented before turning off the exhaust fan. 

KETTLE HEAT SWITCH 

Two position (ON/OFF), lighted rocker switch which operates the heating element in the 

popping kettle, by s

ending power to the “Big Eye” 

electronic temperature control system. 

LIGHT & AUDIBLE LOAD DUMP SIGNAL 

Yellow indicator light and audible sound (if engaged), used to signal Load Dump. 

Therefore, if the yellow light is ON, and the buzzer is sounding, 

one

 of the following 

actions should be taken: 

 

Load the corn and oil 

or

 

 

Dump the popped corn from the kettle 

or

 

 

Turn OFF the Kettle Heat Switch if you are finished popping corn. 

Note:

  This light is also used to indicate Auto Shut Off (if enabled) and Control Board error 

codes (reference the Temperature Control Board section of this manual). 

SALT/SWEET SWITCH (if equipped) 

Two position covered rocker switch used to adjust the kettle temperature for Salt or 

Sweet popping mode. 

OIL DISPENCE PUSH BUTTON SWITCH & GREEN OIL LIGHT (if equipped) 

“Red” Oil Dispense P

ush Button (PB) Switch which dispenses a predetermined amount of oil 

into the kettle when pressed. The Oil System Master Switch must be in the ON position for the 

Oil Dispense PB Switch to activate (reference the Instruction Manual for the oil dispense 

unit). The Green Oil Light on the popper will only light up when the oil pump is dispensing. 

OIL SYSTEM MASTER SWITCH (if equipped) 

Two position, ON/OFF lighted rocker switch - supplies power to the oil pump (either the 

Bag-in-a-Box or Bucket Pump model). Reference the Instruction Manual for the oil 
dispense unit. 

Bag-in-a-Box Model

: Oil System Master Switch ON, provides power to the oil dispense 

unit, activates the warmer/blower, and the heated line kit (if equipped).  

Note: 

Coconut oil will congeal at temperatures below approximately 76°F (24°C). For 

machines used daily, leave the Oil System Master Switch on at all times and keep 

Содержание Macho Pop 2553 Series












































Отзывы: