background image

 

 

Macho Pop

 

Model No. 2553 Series and 2554 Series 

 

Page 6 

 

 

gmpopcorn.com 

 

Electrical Requirements 

The following power supply must be provided:  

Model 2553 Series: 
2553, 2553S, 2553BC, 2553BCS, 2553BCSMM:

 120 V~, 2350 W, 60 Hz 

 

Model 2554 Series: 

2554, 2554S, 2554BC, 2554D:

 120 V~, 1750 W, 60 Hz 

 

 DANGER

 

Machine must be properly grounded to prevent electrical shock to personnel. 
Failure to do so could result in serious injury, or death. 
DO NOT immerse any part of this equipment in water.  
DO NOT use excessive water when cleaning. 
Keep cord and plug off the ground and away from moisture. 
Always unplug the equipment before cleaning or servicing. 
Make sure all machine switches are in the OFF position before plugging the 
equipment into the receptacle. 

008_051514 

 

A certified electrician must furnish sufficient power for proper machine operation and install any 

supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. 

Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold 

Medal Products Co.’s recommendation

 that this machine be plugged directly into a wall outlet. The 

use of extension cords is not recommended due to safety concerns, and may cause sacrificed 

and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset. 

Before You Plug In Machine 

1.

 

Make sure all machine switches are in the OFF position before plugging the equipment 

into the receptacle. 

2.

 

Make sure the wall outlet can accept the grounded plugs (where applicable) on the 

power supply cord. 

3.

 

The wall outlet must have the proper polarity. If in doubt, have a competent 
electrician inspect the outlet and correct if necessary. 

4.

 

DO NOT use a grounded to un-grounded receptacle adapter (where applicable). 

5.

 

Install the unit in a level position. 

 

 

 

CAUTION

 

If the supply cord is damaged, it must be replaced by Gold Medal Products Co., 
its service agent or similarly qualified persons in order to avoid a hazard. 

039_080614 

 

 

 

Содержание Macho Pop 2553 Series












































Отзывы: