background image

Popcorn Topping Dispenser 

 

and Base

 

     Model Series 2396 and 2495 

 

 

Page 3 

 

 

gmpopcorn.com 

 

SAFETY PRECAUTIONS 

 

 DANGER

 

Machine must be properly grounded to prevent electrical shock to personnel. 
Failure to do so could result in serious injury, or death. 
DO NOT immerse any part of this equipment in water.  
DO NOT use excessive water when cleaning. 
Keep cord and plug off the ground and away from moisture. 
Always unplug the equipment before cleaning or servicing. 
Make sure all machine switches are in the OFF position before plugging the 
equipment into the receptacle. 

008_051514 

 

 

 DANGER

 

Improper installation, adjustment, alteration, service, or maintenance can 
cause property damage, injury, or death. Any alterations to this equipment  
will void the warranty and may cause a dangerous condition. This appliance 
is not intended to be operated by means of an external timer or separate 
remote-control system. NEVER make alterations to this equipment. Read the 
Installation, Operating, and Maintenance Instructions thoroughly before 
installing, servicing, or operating this equipment. 

014_020416 

 

 

 

WARNING

 

To avoid burns, DO NOT touch heated surfaces. 
DO NOT place or leave objects in contact with heated surfaces. 

009_092414 

 

 

 

WARNING

 

ALWAYS wear safety glasses when servicing this equipment. 

010_010914 

 

 

 

WARNING

 

No user serviceable parts inside. Refer servicing to qualified service 
personnel. 

011_051514 

 

 

 

WARNING

 

Read and understand operator’s manual and all other safety instructions 
before using this equipment. To order copies of the operator’s manual go to 
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive, 
Cincinnati, OH 45241 USA 1-(800)-543-0862 

022_060215 

 

 

 

Содержание 2396 Series



































Отзывы: