glass 1989 MAWI SPA, Инструкция по установке, эксплуатации и обслуживанию

Страница: 16 / 67

EN
17
•Clean the fi lter(s) at least once per month.
•Check to make sure you have proper circulation throughout your
spa water system.
•Have spa users bathe before entering the spa water.
SPA LEVELING PREPARATION
When the Spa is positioned outside it is preferable to provide
a concrete platform. Other options are brick, stepping stone,
or blocks. It is important to note that soft surfaces, even when
stepping stones are used to evenly distribute the weight of the
spa, will have a tendency to settle, thus resulting in an unleveled
spa.
NOTE: Placing the Spa directly on the grass or on gravel
may increase the amount of debris which is inadvertently
brought into the spa water and may cause harm to your
equipment as well as the spa surface, which are not covered
under warranty.
0
Stepping stones or brick may settle causing the spa to be unlevel.
CAUTION: adjust the central feet of Spa to ensure that they
rest properly on the
fl oor.
Mawi Spa 175/200
STOP
NOTE: the cords to adjust the feet have been positioned
near the pumps.
SPA COVER INSTALLATION
Place the cover squarely on the spa.
NOTE: Keeping the cover in place any time the spa is not
in use will reduce the amount of time the heater operates,
thereby minimizing operating costs.
DANGER.RISK OF INJURY.
•Never leave a spa uncovered or unattended.
•Do not stand, sit, or lie on the cover.
NOTE: please remove coussins (if any) before installing
the cover.
TECHNICAL COMPARTMENT CONNECTIONS
ALL THE PLUMBING WORKS MUST BE CARRIED OUT BY A
QUALIFIED PLUMBING INSTALLER.
ATTENTION: the hydraulic connection must be made to the
mains water network, which is why it must be carried out in
compliance with anti-pollution protection standards. Please
contact local authorities for more information on the rules
governing the discharge of chemically treated water.
Proceed with the connection C1 - F1 on the thermostatic mixer
located under the edge of the tub and with the tub drain O1 (see
chapter “CONNECTIONS DIAGRAM” and product technical
datasheet); then connect the sand
fi lter (optional) and the heat
exchanger (optional), see chapter “SYSTEMS”.
ATTENTION: before starting the spa, test the system to check
the hydraulic connections.
The power box must be connected at the point C.V. (see
installation set-up).Connecting the spa to an improperly wired
circuit will negate many of the spa’s safety features. Improper
wiring may also cause electrocution, risk of
fi re, and other risks
of injuries. Please read and follow the electrical installation
requirements!
SPA MUST BE WIRED IN ACCORDANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES.
ALL ELECTRICAL WORK SHOULDBE DONE BY AN
EXPERIENCED, LICENSED ELECTRICIAN. WE RECOMMEND
THE USE OF APPROPRIATE ELECTRICAL CONDUIT,
FITTINGS, AND WIRE FORALL CIRCUITS.The Spa require a
16 amp, single phase, 220-230 volt, three wire service (one line,
one neutral, one ground). In the cable connecting to the power
box, the earth terminal (Yellow Green) must be at least 30 mm
longer than the phase and neutral conductors. If a stationary
appliance la not
fi tted with a supply cord and a plug, or with
other means for disconnection from the supply mains having
a contact separation in all poles that provide full disconnection
under overvoltage category III conditions, the instructions shall
state that means for disconnection must be incorporated in the
fi xed wiring in accordance with the wiring rules.
The appliance should be supplied through a residual current
device (RCD) with a rated tripping current not exceeding 30 mA.
WARNING: Removing or bypassing any GFCI breaker will
result in an un safe spa and will void the spa’s warranty.
IMPORTANT:
Should you ever fi nd the need to move or relocate
your spa, it is essential
that you understand and apply these installation requirements.
Your spa has been carefully engineered to provide maximum
safety against electric shock. Remember, connecting the spa to
an improperly wired circuit will negate many of its safety features.
CONDUIT INSTALLATION INSTRUCTIONS
1. For the electrical connection, remove the panel that covers
the installation systems compartment.
2. Identify the junction box, loosen the screws and remove the
cover.
3. Connect the power cable to the junction box and wire-up as
shown in the wiring diagram and on the label applied to the inside
of the control box cover.
AVOIDING THE RISK OF ELECTROCUTION
Risk of electrocution
• The spa must be permanently connected to the electricity
supply. The spa must be connected to a Ground Fault Circuit
Interrupter (GFCI). Manufacturer does not supply a GFCI with
the spa. Manufacturer recommends the GFCI be attached to
the end of the spa’s electrical cord. The GFCI must be installed
be a licensed, quali
fi ed electrical. GFCI devices must meet or
exceed all national and local electrical codes.