glass 1989 MAWI SPA, Инструкция по установке, эксплуатации и обслуживанию

Страница: 15 / 67

EN
16
Do not remove the sticker from the product!
Figure A
WARNING.
• Read the manual carefully in all its parts before using the
product.
• Keep this manual for further consultation.
• The manual is intended for di
ff erent models and versions, so
the product may look di ff erent from the manual illustrations.
However the instructions remain unchanged.
• The company reserves the right to make any changes
considered suitable without notice or replacement.
• This product is intended only for the use for which it has been
designed. The manufacturer is not responsible for any damage
caused by improper useage.
• The product identification data (model, power, voltage,
manufacturer’s name) are contained in the silver data plate
on the unit and on the warranty card. It is issued at the time
of testing.
• Make sure that the drain is always e ffi cient.
• Ensure that the fl oor around the product is always dry and
clean, to avoid slips or falls entering or editing the product
itself.
• Use and installation of a cover
• Appliance must be permanently connected to
fi xed wiring.
• Parts containing live parts, except parts supplied with safety
extra-low voltage not exceeding 12 V, must be inaccessible
to a person in the bath.
• When the product is not used, disconnect it completely by
turning o ff the double-pole switch installed on upstream the
appliance.
• Precaution to avoid damage when the appliance is left empty
for an extended period.
All measurements are in mm.
PRE-INSTALLATION REQUIREMENTS
IMPORTANT: given the high capacity and weight of the
spa (see product speci
fi cations), a speci fi c structural and
building services engineering study is necessary.
SITE PREPARATION
You probably have a spot picked out for your new spa, whether
it’s indoors or outdoors, on a patio or on a deck. Just make sure
you check the following:
•Always put your spa on a structurally sound, level surface. A
fi lled
spa is very heavy. Make certain that the location you choose can
support the weight of your
fi lled spa.
•Don’t forget to level your spa before fi lling it. (See the Spa
Leveling Preparation section of this manual.)
•Locate your equipment compartment, which houses all of the
electrical components, in a place where water will drain away
from it. Allowing water into the equipment compartment can
damage the electronics, or may result in tripping your house’s
circuit breaker.
•Leave access to the equipment compartment for periodic spa
care and maintenance.
WARNING: Damage to the spa’s equipment compartment
components or internal plumbing as a result of rodent
infestation is NOT covered under your warranty!
WARNING
Manufacturer recommends that the spa be installed above
ground. Lowering the top of the spa to ground level, or
employing decking which raises standing level toward
the top of the spa substantially increases the hazard of
accidental entry. Consult a licensed building contractor to
design or evaluate your custom decking requirements.
DECK INSTALLATION
To be certain your deck can support your spa, you must know
the deck’s maximum load capacity. Consult a quali
fi ed building
contractor or structural engineer. To fi nd the weight of your spa,
its contents and occupants, refer to the Spa Speci fi cation chart
on back page. This weight per square foot must not exceed the
structure’s rated capacity, or serious structural damage could
result.
INDOOR/BASEMENT INSTALLATION
Be aware of some special requirements if you place your spa
indoors. Water will accumulate around the spa, so
fl ooring
materials must provide a good grip when wet. Proper drainage
is essential to prevent a build-up of water around the spa. When
building a new room for the spa it is recommended that a
fl oor
drain be installed. The humidity will naturally increase with the
spa indoors. Water may get into ironwork and produce oxide,
mildew, or other problems. Check for airborne moisture’s e
ff ects
on exposed wood, paper, etc. in the room. To minimize these
e
ff ects, it is best to provide plenty of ventilation to the spa area.
An architect can help to determine if more ventilation must be
installed.
WARNING: Please keep the area around your spa well
ventilated when it is installed indoors or in a con
fi ned area.
To prevent the formation of condensation inside the space
around the bathtub, make a ventilation system having a
minimum area of 314cm
2
. This system must be made in such a
way as to prevent water in fi ltration.
Inadequate ventilation around the spa could cause a build-up
of a higher-than-normal concentration of spa chemicals and/
or bacterial fragments. These dispersed spa chemicals and/or
bacterial fragments can be inhaled, and may result in breathing
di
ffi culties or lung damage in certain people su ff ering from a
compromised immune system or respiratory infection. If you or
other bathers are a
ff ected by this condition, please seek medical
attention as soon as possible.
In addition to the above, properly clean and maintain your spa
as follows:
•Follow all procedures in this owner’s manual and printed
instructions on all water care (chemical) products packaging.
•Test the water regularly to ensure proper levels of sanitizers,
pH, and other water care requirements.
•Drain, clean, and re
fi ll your spa with fresh water on a regular
schedule, and in accordance with this owner’s manual.