background image

o

Using scissors, cut out push-on cover along the marked lines as required.

o

Push on push-on cover.

i

Alternatively, the detection area can also be limited by switching off individual sensors (see
Commissioning).

5.2 Commissioning

Insert battery into IR remote control

i

To avoid contact problems, keep the contacts of batteries and device free of grease. 

CAUTION!
Risk of chemical burns.
Batteries can burst and leak.
Replace batteries only with an identical or equivalent type.

o

Insert the supplied battery with correct polarity (see IR remote control imprint)

The operation and necessary settings are carried out using the IR remote control for the
installation engineer (see Accessories).

i

If multiple devices are within the range of the IR remote control, then align it so that only
the device to be operated can receive the signals.

Button assignment of the installation engineer IR remote control

Button

Function

1 s 

Ů

Short time operation

30 s 

Ů

2 min 

Ů

5 min 

Ů

30 min 

Ů

Set run-on time

ũ

 Pressing for longer than 10 seconds

Saving ambient brightness as brightness
threshold

Ê

Ŧ

ŧ

Ũ

Setting the brightness threshold

0-1 h

Ů

Setting individual run-on time

Dyn.

Ů

 Pressing for longer than 10 seconds

Switching on the dynamic run-on time

PIR A

PIR B

PIR C

PIR A-C

 Pressing for

longer than 10 seconds

Switching the PIR sensors on/off

PIR A

PIR B

PIR C

 Pressing for less than 10 seconds

In the next 5 seconds, use the 

25 %

50 %

75

%

 and 

100 %

 buttons to set the sensitivity of

the appropriate PIR sensor

25 %

50 %

75 %

100 %

Setting the sensitivity

Ū

 Pressing for longer than 10 seconds

Switching on the Presence detector device
function

ū

 Pressing for longer than 10 seconds

Switching on the Motion detector device
function

Ŭ

 

No function is saved for this device

Test 100 h

 Pressing for less than 10 seconds

Switch on test operation

Test 100 h

 Pressing for longer than 10 seconds

On for 100 hours

Set 1

 Pressing for longer than 10 seconds

Save any changes made for later recall using
the 

Set 2

 button of the end customer IR

remote control

82593212

12.01.2017

12/18

Presence detector and motion detector 360° compact

Содержание 2399 02



















Отзывы: