background image

Cause 2: Device does not detect any motions.

Increase sensitivity.
Switch on all sensors.

Cause 3: Off for 2 hours or Continuous off is activated

Switch on automatic mode.

Device switches on without motions

Cause 1: Presence simulation is activated. Device switches at saved times.

Switch the presence simulation off.

Cause 2: Interference sources in the detection area.

Remove interference sources if possible.
Reduce sensitivity.
Limit detection area.

Device constantly switches on and off during motion

Cause 1: Short-time operation is switched on.

Set a longer run-on time.

Device switches off despite motion

Cause 1: The device does not detect any motion.

Increase sensitivity.

Cause 2: Detection area is limited because a sensor was switched off.

Switch on all sensors.

Cause 3: Detection area is limited by push-on cover.

Check the push-on cover.

Device does not switch off

Cause 1: Interference sources in the detection area, device detects motions constantly.

Remove interference sources if possible.
Reduce sensitivity.
Limit detection area.

Cause 2: On for 2 hours, Continuous on or On for 100 hours is activated.

Switch on automatic mode.

The device does not respond to IR remote control, red LED does not flash.

Cause 1: IR remote control out of range.

Go closer to the motion detector.

Cause 2: Battery in IR remote control is empty.

Change battery (see back of the IR remote control)

The device does not respond to IR remote control, red LED flashes, blue LED does not

Cause: Device is receiving an IR signal. Function or setting cannot be executed.

6.3 Accessories

IR remote controller PIR 1 (installer)

Order No. 2382 00

6.4 Warranty

The warranty follows about the specialty store in between the legal framework as provided for
by law 
Please submit or send faulty devices postage paid together with an error description to your
responsible salesperson (specialist trade/installation company/electrical specialist trade). They
will forward the devices to the Gira Service Center.

82593212

12.01.2017

17/18

Presence detector and motion detector 360° compact

Содержание 2399 02



















Отзывы: