GIESSE 07888, Инструкция по установке и эксплуатации

Страница: 25 / 64

25
5. Mount the bracket for outward opening windows onto the moveable part of the frame in accordance with the markings
indicated on the template.
6. Complete assembly of the chain terminal with the safety clip inserted onto the provided pin Ø4x32 in median position (see fig.
15).
7. Mount the two brackets on to the sides of the actuator.
8. Position the actuator onto the window frame and line up with the holes bored earlier. Fix the actuator.
9. Bring the chain terminal up to the bracket and insert the pin into the hole on the bracket. Attach the safety clip to the bracket.
10.
Check that the exit of the chain is perfectly aligned with the bracket. If the chain is not aligned, loosen the fixing screws and
reposition the bracket correctly.
11. Check all electrical connections with the diagram on the label attached to the lead and in conformity to indications on
chapter 9
– Electrical connection.
12. Carry out a complete check of opening and closure of the window. Once the closure phase has been completed, check that
the window frame is completely closed by checking the pressure on the weather strips
15. Meaning of the LED flashing mode
The LED can be seen on the electronic board after removing the closure plug. In some cases it flashes in different ways
depending on the signal it is emitting; the different flashing modes indicate the precise behavior of the actuator during the
programming of the machine, radio remote control or rain sensor.
The table below summarizes the meaning of the LED flashing mode.
Ref. Flashing
Flashing
frequency
Meaning
1 Off Actuator at rest, no alarm is active
2 Steady-on Function not provided for
3
Slow flashing
for 10 seconds
1 per second
The machine is waiting to receive a
valid radio remote control code.
4
On for
2 seconds
Steady-on
The machine has saved the radio
remote control correctly
5
Flashing for
2 seconds
2 per second
The machine has not saved the radio
remote control
6
Fast continuous
flashing
2 per second Rain sensor active
7
Flashing for 5
seconds
2 per second
Erasing the radio remote control
memory
16. Checking for correct assembly
•
Check that the window has closed completely, even at the corners, and check there are no obstacles caused by assembly in
the wrong position.
•
Check that when the window frame is closed, the chain terminal is at least a couple of millimetres distant from the actuator
body. This will ensure correct closure of the window with correct pressure on the weather stripping. If the chain terminal is not
positioned as stated there is no guarantee the window will close correctly.
•
Check that all attachments and support brackets are tightly fixed to the window frame and that all screws are correctly
tightened.
•
Check that the window moves to the desired position in accordance with the limit switch selected.
•
Check that the gear motor support brackets are aligned and the four fixing screws are firmly screwed into position.
17. Emergency manoeuvres, maintenance and cleaning
Should the window have to be opened manually in the event of no electricity, mechanical failure, or for normal maintenance or
cleaning of the external surface of the window frame, the following instructions should be followed:
1. Release the safety clip locking the chain terminal to the bracket.
2. Hold the window with one hand and pull the pin out of the opening with the other hand (Fig. 16).
3. Manually open the window frame.
A
TTENTION
:
DANGER
– the window could fall as the sash is no longer held in position by
the chain .
4. After maintenance and/or cleaning repeat points 1 and 2 in reverse order.
18. Troubleshooting
Please consult the following table for any eventual problems with function during installation or normal use:
Problem Possible cause Solution
Actuator doesn’t work
•
No electricity supply for feeder.
•
Connecting cable not connected or wire not
connected.
•
Winder on the transformer is broken.
•
Check state of safety switch.
•
Check all electrical connections of gear
motor.
•
Contact the Giesse technical support.
Figure 16