Giant UGC120S-100 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 54

background image

10

GI-IM048En-1013

C. CLEARANCES FOR SERVICE ACCESS

Figure 1: Minimum Service Clearances

NOTE:

If you do not provide the minimum clearances shown in Figure 1, it might not be possible to service the heater without removing

it from the space.

The space must be provided with combustion/ventilation air openings correctly sized for all other appliances located in the same space
as the heater. The heater cover must be securely fastened to prevent the heater from drawing air form the heater room. This is
particularly important if the heater is in a room with other appliances. Failure to comply with the above warnings could result in
substantial property damage, severe personal injury, or death.

D. RESIDENTIAL GARAGE INSTALLATION

PRECAUTIONS

If the heater is located in a residential garage, per ANSI Z223.1:



Mount the bottom of the heater a minimum of 18” (46 cm) above the floor of the garage, to ensure the burner and ignition
devices are well off the floor.



When raising the heater, fully support the entire bottom of the water heater.



Locate or protect the heater so it cannot be damaged by a moving vehicle.

E. EXHAUST VENT AND INTAKE PIPE

The heater is rated ANSI Z21.10.3 Category IV (pressurized vent, likely to form condensate in the vent) and requires a special vent
system designed for pressurized venting.

NOTE: The venting options described here (and further detailed in Venting, Part 5 in this manual) are the lone venting options
approved for this water heater. Failure to vent the water heater in accordance with the provided venting instructions will void
the warranty.

Failure to vent the water heater properly will result in serious personal injury or death.

Vents must be properly supported. Heater exhaust and intake connections are not designed to carry heavy weight. Vent support
brackets must be within 1’ (30 cm) of the heater and the balance at 4’ (1.2 m) intervals. Heater must be readily accessible for visual
inspection for the first 3’ (91 cm) from the heater.

«
...
8
9
10
11
12
...
»

Содержание UGC120S-100























































Отзывы:

Нет отзывов

Похожие инструкции для UGC120S-100

Бренд: Jet-Line Страницы: 20

Бренд: Fahrenheat Страницы: 6

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 57

Safe-T FURNACE HC-445

Бренд: Pelonis Страницы: 6

Бренд: Haverland Страницы: 64

Vectissimo CO180

Бренд: Rowenta Страницы: 10

Бренд: Ulvac Страницы: 27

Бренд: Kohler Страницы: 13

Бренд: Milton Roy Страницы: 43

Бренд: wallas Страницы: 29

Бренд: N'oveen Страницы: 66

Бренд: Nibe Страницы: 20

BREDEL 701 Series

Бренд: Watson-Marlow Страницы: 25

Cylinder Passport

Бренд: WarmFlow Страницы: 16

Бренд: Berner Страницы: 16

Бренд: MV Heating Страницы: 19

Бренд: Jaga Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды