Giant UGC120S-100 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 54

background image

29

GI-IM048En-1013

Be sure to locate the heater such that the exhaust vent and intake piping can be routed through the building and properly terminated.
Different vent terminals can be used to simplify and eliminate multiple penetrations in the building structure (refer to the Venting
Section). The exhaust vent and intake piping lengths, routing and termination methods must all comply with the methods and limits
given in the Venting section, Part 5 of this manual.

When installing a combustion air intake from outdoors, care must be taken to utilize uncontaminated combustion air.

NOTE: To

prevent combustion air contamination, see Table 1

: Contaminant Table.

Take extra precaution to adequately support the weight of vent pipes terminating through the roof. Failure to properly support roof
terminated vent piping could result in property damage, serious personal injury, or death due to flue gas leakage.

«
...
27
28
29
30
31
...
»

Содержание UGC120S-100























































Отзывы:

Нет отзывов

Похожие инструкции для UGC120S-100

Бренд: EarthLinked Страницы: 6

Бренд: Calpeda Страницы: 43

Бренд: SereneLife Страницы: 10

Бренд: VTS Medical Systems Страницы: 23

Бренд: Rinnai Страницы: 31

UNI_SAUNA_B4.5KW

Бренд: UNIPRODO Страницы: 17

SMART ECG 1000 A

Бренд: Airtecnics Страницы: 22

Бренд: Culligan Страницы: 58

Бренд: EQUATION Страницы: 34

Бренд: Watts Страницы: 22

Бренд: Graco Страницы: 32

Бренд: Edwards Страницы: 60

Бренд: RadonAway Страницы: 22

Бренд: ACE INSTRUMENTS Страницы: 3

Beta b BT4b Series

Бренд: ProMinent Страницы: 108

Бренд: Malmbergs Страницы: 12

FWH OTTIMO 501CH

Бренд: Faber Страницы: 12

Бренд: Radiatori 2000 Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды