manualshive.com logo in svg

GFS Performer ES, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
GFS Performer ES Скачать руководство пользователя страница 7

WARNING
Local fire and building codes require fire protection. Check with local inspector authorities for requirements.

CAUTION
Read and save these instructions before attempting to assemble, install, operate, or maintain the product
described. Protect yourself and others by observing all safety information. Failure to comply with
instructions could result in personal injury and/or property damage. Retain these instructions for future
reference.

CAUTION
This manual contains statements that relate to worker safety. Read this manual thoroughly and comply as
directed. Operate this equipment in accordance with the guidelines set forth in this manual. It is impossible
to list all potential hazards of this equipment. Instruct all personnel involved with this equipment in the safe
conduct and operation of the system. GFS recommends that only qualified personnel operate and maintain
this equipment.

CAUTION
Safety signs, panels, and labels that are normally affixed to the product must be replaced immediately if
illegible or missing.

CAUTION
New or replacement parts that are installed during repair or maintenance must include all safety signs,
panels, and labels as specified by the manufacturer. These must be affixed to the new or replacement parts
as specified by the manufacturer.

CAUTION
Where applicable, use earplugs or take other safety measures for hearing protection.

NOTICE
The product must be installed and serviced only by a trained, qualified service technician. Incorrect
installation may void the warranty.

NOTICE
If you have questions about the warranty, please contact your distributor prior to contacting GFS.

General safety

Global Finishing Solutions

7

239-062 rev 5

Содержание Performer ES


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды