manualshive.com logo in svg

GFS Performer ES, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
GFS Performer ES Скачать руководство пользователя страница 37

• Perform the task below if the brightness of the lights seems diminished overall and if you use a protective

covering on the booth lights.

NOTE
GFS recommends that you use Light Fixture Lens Protector or GFS Booth Shield to protect your booth
lights from overspray. Lens Protector is a plastic peel-off film; Booth Shield is a peelable coating. Both
products are available from your local distributor or from the GFS Parts Department. For more information,
see “Accessories” (page 45).

1.

Remove the protective covering from all lights:

• If you use Lens Protector: Remove the Lens Protector plastic sheet.

• If you use Booth Shield: Score around the edges and peel the clear Booth Shield covering off the

surfaces.

2.

Discard the used covering.

3.

Apply a fresh layer of protective covering over all the lights:

• If you use Lens Protector: Apply a new plastic sheet.

• If you use Booth Shield: Reapply the clear Booth Shield and wait for it to dry.

Service and maintenance

Global Finishing Solutions

37

239-062 rev 5

Содержание Performer ES


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды