manualshive.com logo in svg

GFS Performer ES, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
GFS Performer ES Скачать руководство пользователя страница 33

Type

Allowable Valve Seat Leak-
age up to 7 PSI inlet

Air

# of Bubbles in 10
s Natural Gas

LP

DMV D(LE) 701/622

239 cc/hr

5

6

4

DMV-D(LE) 702/622

464 cc/hr

9

11

7

DMV-D(LE) 703/622

464 cc/hr

9

11

7

IMPORTANT
If leakage values are exceeded, replace valve immediately.

7.

Repeat the same procedure for valve V2 (port 3). (Energize terminal 2 on the DIN connector to open
valve 1.)

8.

Verify that the downstream manual ball valve is closed and both automatic safety shutoff valves are de-
energized.

9.

Remove the flexible hose, and close all test nipples.

10. With the upstream manual ball valve open, energize both automatic safety shutoff valves.

11. Use soapy water to check all test nipples to ensure that there are no leaks.

12. If no leakage is detected, de-energize all automatic safety shutoff valves, and open the downstream

manual ball valve.

If applicable: Check the gas pressure switches

Check the low-pressure and high-pressure switches once a year for proper operation.

Low-pressure gas switch

Perform these tasks to check the resistance of the low-pressure switch both in normal operation and in a
fault state.

NOTE
A resistance of more than 1.0 ohm indicates that the switch contacts are starting to either corrode or
carbonize.

1.

Connect a meter capable of r/- 0.1 ohms to the NO and COM contacts.

Service and maintenance

Global Finishing Solutions

33

239-062 rev 5

Содержание Performer ES


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды