+GF+ SG 160 Скачать руководство пользователя страница 54

Страница: 54 / 60

10 Maintenance

Operating instructions SG 160

10 Maintenance

The SG 160should be checked and cleaned periodically.

Standard care of the SG 160 is limited to periodic cleaning of the outside.

If the planer chain needs to be tightened or replaced, the motor can be turned
eccentrically by loosening the socket head screws.

10.1

Replacement of worn parts

•

PTFE coating of the heating element:

Clots, cracks or other damage:

–

heating element needs to be recoated

–

send the heating element to the nearest service center or to the
manufacturer (see the back of this manual).

Danger of injury!

Sharp planer blades!

Danger of cutting if the planer blades, which are sharp on both sides, are
touched.

•

The planer blades on the planer should be replaced periodically.

For order number see spare parts list.

We recommend having a service booklet to record maintenance work for each
SG 160machine.

Date

Service

Repair

Comments

15.09.2010

B. Muster

Everything OK

25.10.2011

E. Service Heater

Cable replaced

CAUTION

Service booklet

Example:

Содержание SG 160





























































Результаты поиска

Содержание SG 160

Отзывы:

Похожие инструкции для SG 160

Бренды по названию

Популярные бренды

+GF+ SG 160, Инструкция по эксплуатации

Результаты поиска

Содержание SG 160

Отзывы:

Похожие инструкции для SG 160

Бренды по названию

Популярные бренды