GENUINE HOOLIGAN 170i Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 146

background image

Information Summary and Preparation

-1

1-5 Code of practice:

1.

Any clamp or cotter pin removed shall be replaced with a new one.

2.

Any part to be replaced shall be manufactured by Motive Power.

3.

Make sure of any assembled component securely fastened and formally activated.

4.

Any bolts or nuts with large external diameters rather than small ones shall be screwed first and
diagonally according to rated torque values as follows.

5.

Any mechanic shall use specific or common tools for any disassembly and wear work shoes
during maintenance.

6.

The safety of any maintenance operation practiced by two mechanics shall be ensured each
other.

7.

Any electrical parts slightly heated with the motorcycle started are normal and not touched by
hands directly.

8.

Please keep any cable or wire harness to be installed properly fixed but not excessively
tensioned or loosened without any acute (or sharp) angle or bulged bolt (or screw) piercing a
cable. Check any cable or wire harness installed for any unnecessary twist or kink.

9.

Do not put any tool on the motorcycle, particularly the battery unit to become a short circuit,
during maintenance.

10.

The battery in a motorcycle which has not been started for a long period shall be tested once to
ensure its voltages and charged per month.

11.

Please follow the correct steps to connect and disconnect a lead acid battery without the short
circuit or inflammation.

1-5.1 Directions for maintenance of the Engine Management System (EMS)

1) Directions for General Maintenance

Any check to the Electronic Management System shall be made with a multi-meter only.
1.

To make sure of the Electronic Management System properly running, please use parts
supplied by Motive Power during maintenance.

2.

Any operation to clean parts during maintenance shall be executed in a well-ventilated place.

3.

Please follow the directions for steps of maintenance and diagnosis.

4.

Do not disassemble or remove parts in the Electronic Management System during
maintenance.

5.

Please keep watch for any electronic element (electronic control unit, sensor, etc.) not fallen to
the ground during maintenance; establish the environmental protection concept for any waste
from maintenance invalidly disposed.

6

«
...
4
5
6
7
8
...
»

Содержание HOOLIGAN 170i



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для HOOLIGAN 170i

Бренд: b'Twin Страницы: 18

Бренд: ICONE Страницы: 24

Бренд: IconBiT Страницы: 24

Бренд: Direct Bikes Страницы: 16

STEPS DIN EN 15194

Бренд: Hermann Страницы: 52

Бренд: Master Страницы: 46

Бренд: EOVOLT Страницы: 24

Бренд: Yedoo Страницы: 96

Бренд: HALOBOARD Страницы: 20

Бренд: wayscral Страницы: 149

Бренд: BLUETOUCH Страницы: 73

Бренд: Acer Страницы: 35

Espark 13111290

Бренд: Razor Страницы: 14

Бренд: W-Tec Страницы: 15

Бренд: Victesse Страницы: 21

Бренд: Verhagen Leiden Страницы: 19

Бренд: UrbMob Страницы: 8

Бренд: ROAD KING Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды