Genie Z-45J Скачать руководство пользователя | Manualshive

Страница: 71 / 74

background image

Fifth Edition • First Printing

Operator's Manual

Specifications

Part No. 1297032GT

Z

®

-

45J DC • Z

®

-45J Bi-Energy

69

Specific ati ons

Z-45J DC (jib)

Height, working maximum

51 ft 9 in

15.9 m

Height, platform maximum

45 ft 9 in

13.9 m

Height, stowed maximum

6 ft 7 in

2.0 m

Horizontal reach,
platform 90°, maximum

25 ft 1 in

7.7 m

Width

5 ft 10.3 in

1.79 m

Length, stowed

22 ft 5 in

6.83 m

Maximum load capacity

500 lbs

227 kg

Maximum wind speed

28 mph

12.5 m/s

Wheelbase

6 ft 8 in

2.0 m

Turning radius (outside)

14 ft

4.3 m

Turning radius (inside)

6 ft

1.8 m

Turntable rotation

355°

Turntable tailswing

0 in

0 cm

Power source

8 Group 903, L-16,

6V 390AH Batteries

Drive speed, stowed

3.0 mph

40 ft/9 sec

4.8 km/h

12.2 m/9 sec

Drive speed, booms
raised

0.6 mph

40 ft/45 sec

1 km/h

12.2 m/45 sec

Airborne noise emissions

73 dB

Maximum sound level at normal operating workstations
(A-weighted)

Ground clearance, center

9.5 in

24.1 cm

Ground clearance, minimum

7.5 in

19.1 cm

Weight

16,300 lbs

7394 kg

(Machine weights vary with option configurations. See
serial label for specific machine weight.)

Ambient operating temperature

-20° F to 120° F

-29° C to 49° C

Platform dimensions, 6 foot (length
x width)

72 in x 30 in

1.8 m x 76 cm

Platform dimensions, 5 foot (length
x width)

60 in x 30 in

1.5 m x 76 cm

Platform dimensions, 4 foot (length
x width)

48 in x 30 in

1.2 m x 76 cm

Platform leveling

self-leveling

Platform rotation

160°

Controls

24V DC proportional

AC outlet in platform

Standard

Hydraulic pressure, maximum
(boom functions)

3200 psi

221 bar

System voltage

48V

Tire size, 2WD Industrial
Foam filled only

9-14.5 LT

Fuel tank capacity

9 gallons

34.1 liters

Maximum slope rating, stowed position

Platform downhill

30% (17°)

Platform uphill

20% (11°)

Side slope

25% (14°)

Note: Slope rating is subject to ground conditions with
one person in the platform and adequate traction.
Additional platform weight may reduce slope rating.

Floor loading information

Tire load maximum

8100 lbs

3674 kg

Tire contact pressure

100 psi

7.03 kg/cm2

689 kPa

Occupied floor pressure

315 psf

1538 kg/m

2

15.08 kPa

Note: Floor loading information is approximate and does
not incorporate different option configurations. It should
be used only with adequate safety factors.

Continuous improvement of our products is a Genie
policy. Product specifications are subject to change
without notice or obligation.

«
...
69
70
71
72
73
...
»

Содержание Z-45J











































































Отзывы:

Нет отзывов

Похожие инструкции для Z-45J

Бренд: Eaton Страницы: 18

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: SMT Страницы: 24

Бренд: GREER Company Страницы: 35

Бренд: Reflex Страницы: 26

Бренд: Unimig Страницы: 14

Бренд: FAAC Страницы: 16

Бренд: Nedap Страницы: 5

Бренд: H&S AUTOSHOT Страницы: 19

Бренд: Maco Страницы: 40

Бренд: Dibipack Страницы: 41

Бренд: WPG Страницы: 46

Prism Medical 303090

Бренд: Handicare Страницы: 26

Бренд: HTP Страницы: 36

Protecta series

Бренд: 3M Страницы: 16

Бренд: Migatronic Страницы: 36

DuroZone SMZ-AC

Бренд: Duro Dyne Страницы: 12

POWER FEED 10 ROBOTIC K1780-1

Бренд: Lincoln Electric Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды