Genie Z-45J Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 74

background image

Operator's Manual

Fif

th Edition • First Printing

Controls

34

Z

®

-

45J DC • Z

®

-45J Bi-Energy

Part No. 1297032GT

Platform Control Panel

1

Horn button

Press this button and the horn will sound.
Release the button and the horn will stop.

2

Auxiliary power switch with cover

Use auxiliary power if the primary power
source fails.

Simultaneously hold the auxiliary power switch
on and activate the desired function.

3

Drive enable indicator light

Light on indicates that the boom has moved
just past either non-steer wheel and drive
function has been interrupted.

4

Drive enable switch

To drive when the drive enable light is on, hold
the drive enable switch to either side and
slowly move the drive control handle off
center. Be aware that the machine may move
in the opposite direction that the drive and
steer controls are moved.

5

Z-45/25J: Jib boom up/down switch

Move the switch up and
the jib boom will raise.
Move the switch down
and the jib boom will
lower.

6

Platform rotate switch

Move the platform rotate
switch to the right and the
platform will rotate to the
right. Move the platform
rotate switch to the left
and the platform will rotate
to the left.

7

Platform level switch

Move the platform level
switch up and the level of
the platform will raise.
Move the platform level
switch down and the
level of the platform will
lower.

8

Used for optional equipment

9

Bi-Energy models: Glow plug switch

Move the glow plug switch to either side and
hold for 3 to 5 seconds.

10

Bi-Energy models: Engine start switch

Move the engine start switch to either side to
start the engine.

11

Bi-Energy models: Engine idle (rpm) select
switch

Move the switch to the left (rabbit & foot
switch) for foot switch activated high idle.

Move the switch to the center (turtle) for low
idle.

Move the switch to the right (rabbit) for high
idle and quickest battery charging.

12

Platform overload indicator light

Light flashing indicates the platform is
overloaded and no functions will operate.
Remove weight until the light goes off.

13

Machine not level indicator light

Light flashes when the platform is raised and
the machine is on a severe slope. The drive
function in one or both directions will not
operate.

«
...
34
35
36
37
38
...
»

Содержание Z-45J











































































Отзывы:

Нет отзывов

Похожие инструкции для Z-45J

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: ICP DAS USA Страницы: 6

Бренд: ubbink Страницы: 7

Бренд: STAYER WELDING Страницы: 56

Бренд: Barton Страницы: 36

Бренд: M-system Страницы: 6

Бренд: CIGWELD Страницы: 116

Бренд: Telpro Страницы: 6

Бренд: Telwin Страницы: 56

Бренд: Ravaglioli Страницы: 68

Бренд: M-system Страницы: 3

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 28

Бренд: Cattron Страницы: 121

Бренд: Würth Страницы: 292

PRO-POWER VIMSF100

Бренд: VITO Страницы: 48

Бренд: National Instruments Страницы: 49

Бренд: Ausmig Страницы: 24

Бренд: VMB Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды