Genie Z-45J Скачать руководство пользователя страница 59

Страница: 59 / 74

Fifth Edition • First Printing

Operator's Manual

Operating Instructions

Part No. 1297032GT

45J DC • Z

-45J Bi-Energy

To Drive

Press down the foot switch.

Increase speed: Slowly move the control
handle off center.

Decrease speed: Slowly move the control
handle toward center.

Stop: Return the control handle to center or
release the foot switch.

Use the color-coded direction arrows on the
platform controls and the drive chassis to identify
the direction the machine will travel.

Machine travel speed is restricted when the booms
are raised or extended.

Drive Enable

Light on indicates that the boom
has moved just past either non-
steer wheel and the drive
function has been interrupted.

To drive, hold the drive enable switch to either side
and slowly move the drive control handle off
center.

Be aware that the machine may move in the
opposite direction that the drive and steer controls
are moved.

Always use the color-coded direction arrows on
the platform controls and the drive chassis to
identify the direction the machine will travel.

Driving on a slope

Determine the uphill, downhill and side slope
ratings for the machine and determine the slope
grade.

Maximum slope rating, platform
downhill (gradeability):

30% (17°)

Maximum slope rating, platform
uphill:

20% (11°)

Maximum side slope rating:

25% (14°)

Note: Slope rating is subject to ground conditions
with one person in the platform and adequate
traction. Additional platform weight may reduce
slope rating. The term gradeability applies to the
platform downhill configuration only.

Be sure the boom is below horizontal and the
platform is between the non-steer wheels.

Move the drive speed select switch to machine on
incline symbol.

Содержание Z-45J











































































Результаты поиска

Содержание Z-45J

Отзывы:

Похожие инструкции для Z-45J

Бренды по названию

Популярные бренды

Genie Z-45J, Руководство оператора

Результаты поиска

Содержание Z-45J

Отзывы:

Похожие инструкции для Z-45J

Бренды по названию

Популярные бренды