4 - 16
Genie Z-45/25 & Genie Z-45/25J
Part No. 52709
First Edition • Second Printing
Section 4 • Scheduled Maintenance Procedures
24 Move the lift/drive select switch to the drive
position (if equipped).
25 Press down the foot switch and slowly move the
drive control handle off center.
Result: The machine should move at a reduced
drive speed.
26 Move the lift/drive select switch to the lift
position (if equipped).
27 Press down the foot switch and lower the
secondary boom to the stowed position, then
extend the primary boom approximately 2 feet
(0.6 m).
28 Move the lift/drive select switch to the drive
position (if equipped).
29 Press down the foot switch and slowly move the
drive control handle off center.
Result: The machine should move at a reduced
drive speed.
Drive speed, maximum,
raised or extended
Drive speed, boom
0.6 mph
raised or extended,
1.0 km/h
Standard Base Models
40 ft/45 sec
12.2 m/45 sec
Drive speed, boom
0.36 mph
raised or extended,
0.58 km/h
Narrow Base Models
40 ft/79 sec
12.2 m/79 sec
Drive Enable Limit Switch
A properly functioning drive enable limit switch is
essential for safe machine operation and
workplace safety. The drive enable limit switch
stops the drive function when the boom is rotated
past a non-steer tire and alerts the operator that
the machine may drive in the opposite direction
that the drive and steer control handle is moved.
1 Start the engine from the ground controls and
rotate the boom between the steer and
non-steer tires. Turn the engine off.
2 Visually inspect the drive enable limit switch for
the following:
· Broken or missing roller or arm
· Missing fasteners
· Loose wiring
a
turntable
b
drive enable limit switch (LS4)
c
turntable rotation bearing
a
b
c
TABLE
A
PROCEDURES
Содержание Z-45 XC
