General Pump HF Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 27

background image

Page 17

Serial #10127003 and Later

HF SERIES

GENERAL PUMP

A member of the Interpump Group

Conclusion: with a wheelbase of 23.62 (600 mm) and with a dynomometer, loading the belt branch with 16.86 ft lbs

(75 N) as indicated in fig, a “te” bend of approximately 0.43 in (10.8 mm) is obtained.

Fig. 12

Lf = Wheelbase

te = Belt bend

Fe = 75 N Dynamometer load

Note 1 •

Unless otherwise stated by the supplier of the belts, control of proper pull and its relative re-tensioning should

be performed after no less than 30 minutes of motion necessary for the normal adjustment of the belts. Best perfor-

mance and durability will be achieved with proper tensioning.

Note 2 •

In case of necessity or for routine maintenance, never replace a single belt but the complete set.

9.13 Transmission of Power From the Second PTO

Upon request, HF series pumps can be supplied with an auxiliary PTO on the opposite side to the driver (transmission

of power from the second PTO).

Ref 300764 Rev. F

05-21

«
...
15
16
17
18
19
...
»

Содержание HF Series




























Отзывы:

Нет отзывов

Похожие инструкции для HF Series

Бренд: Gardena Страницы: 17

Бренд: Davey Страницы: 12

Бренд: Barmesa Pumps Страницы: 42

Бренд: Jandy Страницы: 108

Бренд: Balcrank Страницы: 18

Бренд: Underhill Страницы: 2

Бренд: Annovi Reverberi Страницы: 18

COBRA DS 0600 E

Бренд: BUSCH Страницы: 24

Бренд: T.I.P. Страницы: 136

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

Бренд: Sam Страницы: 23

Powerflex PDVG-40T42

Бренд: American Water Heater Страницы: 4

Habitat PWF105-C

Бренд: Plantronics Страницы: 33

Бренд: EXTOL Страницы: 28

MiniTank WM-2.5

Бренд: Waiwela Страницы: 20

Бренд: ACE INSTRUMENTS Страницы: 3

Бренд: Binks Страницы: 40

Бренд: D-D The Aquarium Solution Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды