General Pump HF Series Скачать руководство пользователя страница 7

Страница: 7 / 27

Page 7

Serial #10127003 and Later

HF SERIES

7. GENERAL INFORMATION ABOUT PUMP USE

The HF pump has been designed to operate in environments with atmospheres that are not potentially

explosive, with filtered water (see par. 9.7) and at a maximum temperature of 104° F (40° C). Other liquids can

be used only upon approval by

Customer Service Department.

7.1 Water temperature

Water temperature is critical for the pump life, the higher it is, the more likely it is to create cavitation, resulting in pre-

mature seal and valve failures. The maximum permissible water temperature is 104° F (40° C). However, the pump can

be used with water temperature of 140° F (60° C), but only for a short period of time. In this case, it is best to consult

Customer Service Department.

7.2 Maximum Pressure and Flow Rate

The performance data indicated in the catalog and on the rating plate refer to the maximum performance of the pump.

The use of the pump below the rated performances does not allow the drop in power absorbed to be balanced by

altering the pressure or volume of the pump above its maximum value unless especially authorized by our

Customer

Service Department.

7.3 Lowest operating RPM

The lowest operating speed allowed for these types of pumps is 100 RPM for non-continuous periods; any rpm

other than as shown in the performance table (see chapter 5) must be expressly and authorized

Customer Service

Department.

BRAND

TYPE

GENERAL PUMP

SERIES 220

ARAL

Aral Degol BG220

ENERGOL HLP 220

CASTROL

Hyspin VG 220, Magna 220

ELF

POLYTELIS 220

ESSO

NUTO 220

FINA

Cirkan 220

FUCHS

RENOLIN 220

MOBIL

DTE OIL BB

SHELL

TELLUS C 220

TEXACO

RANDO HD 220

TOTAL

CORTIS 220

7.5 Brands and Types of Oil Recommended

The pump is supplied with oil suitable for room temperatures for 32° F to 86° F (0° C to 30° C).

Some types of recommended oil are indicated in the table below, these oils have additives to increase corrosion resis-

tance and fatigue resistance (DIN 51517 Part 2). Alternatively you can also use Automotive Gear SAE 85W-90 oil.

GENERAL PUMP

A member of the Interpump Group

7.4 Vibration

The detection of vibration shall be carried out only with the pump set up on the plant and at the performance declared by

the customer. Values must be in accordance with regulations.

Ref 300764 Rev. F

05-21

Содержание HF Series




























Результаты поиска

Содержание HF Series

Отзывы:

Похожие инструкции для HF Series

Бренды по названию

Популярные бренды

General Pump HF Series, Руководство пользователя

Результаты поиска

Содержание HF Series

Отзывы:

Похожие инструкции для HF Series

Бренды по названию

Популярные бренды