General Pump HF Series Скачать руководство пользователя страница 3

Страница: 3 / 27

Page 3

HF SERIES

1. INTRODUCTION

Please read this manual carefully before using your HF Series pump.

It contains the necessary information for correct installation, use and maintenance as well as some

practical suggestions for trouble shooting. Providing your HF high pressure plunger pump is correctly installed and main-

tained, it will give trouble free operation for a long time. The manufacturer declines all responsibility for

damages arising from the misuse and non-observance of the instructions indicated in this manual. On receiving the

pump, please check that it is complete and in good state.

Should you find anything out of order, please contact General Pump before installing and starting the pump.

2. SYMBOL DESCRIPTIONS

Warning

Potential Danger

Danger

Electrocution Danger

Danger

Wear protective mask

Danger

Wear goggles

Danger

Wear protective gloves

Danger

Wear protective boots

Read carefully and understand

the manual before operating

the pump

Serial #10127003 and Later

GENERAL PUMP

A member of the Interpump Group

Ref 300764 Rev. F

05-21

Содержание HF Series




























Результаты поиска

Содержание HF Series

Отзывы:

Похожие инструкции для HF Series

Бренды по названию

Популярные бренды

General Pump HF Series, Руководство пользователя

Результаты поиска

Содержание HF Series

Отзывы:

Похожие инструкции для HF Series

Бренды по названию

Популярные бренды