Generac Power Systems quietpact 85d Скачать руководство пользователя страница 24

Страница: 24 / 112

2.1 LOCATION AND SUPPORT

Be sure the installation complies with all standards and codes

listed in the "Standards Booklets" section of this manual.

2.1.1 GENERATOR

LOCATION

The most desirable location for the generator set is between the

vehicle's main frame members.
Many recreational vehicles have been factory-equipped with an

area for the generator set. Some may even have a generator com-

partment provided by the vehicle manufacturer.
Plan the generator location based on the following:
• The generator set must be installed on a framework that is

part of the recreational vehicle, as outlined in the "Generator

Support" section.

• The location must provide an access opening that is large

enough to permit generator removal (unless the generator is to

be removed from underneath the supporting framework).

• The location must provide easy access to frequently serviced

components, such as, filters, oil drains, and other common

maintenance parts.

• The location must provide sufficient room to allow minimum

clearances for air circulation. If sound insulation is to be

used on the compartment walls and ceiling, the minimum

recommended clearance applies to the space between the

generator and such insulation.

• The location must provide adequate cooling and ventilating air-

flow for the generator, without a great deal of work and expense.

2.1.2 GENERATOR

SUPPORT

The generator must be securely attached to a metal framework that

has been affixed to the vehicle frame structure by bolting or welding.

The metal framework on which the generator will rest, and which will

restrain the generator set, should consist of at least two horizontal

beams. These beams should consist of (a) 1-1/2-inch square,

11-gauge steel tubing OR (b) 1-1/2-inch, 11-gauge angle iron.
The generator can be installed so that it sits on top of the horizontal

support tubing, if the vehicle design permits. Another method is

to suspend the generator below the horizontal support tubing by

means of suitable, structurally-sound metal framework. The fol-

lowing general rules apply:
• Vehicle construction MUST be capable of supporting the weight

of the generator.

• Whether the generator is mounted above the horizontal support

tubing or suspended below the tubing, the supporting frame

used must be structurally sound.

• If the generator cannot be bolted directly to the supporting

frame or support tubing, consider using additional tubing,

angle brackets or other supports to give the supporting frame

sufficient strength.

2.1.3 SUSPENDED

MOUNTING

If the generator will be suspended below the horizontal support

tubing, the suspension method used with the vehicle frame mem-

bers must (a) be able to support the weight of the generator AND

(b) provide sufficient restraint for the generator. One typical sus-

pended mounting system is shown in Figure 2.1. The location of

a suspended mounting system must be carefully planned, keeping

the following general rules in mind:
• Protect the generator against road splash and debris. Baffles or

splash guards may be required to protect certain areas of the

generator. To make sure the generator is adequately protected,

road-test the installation through mud, water, and slush.

Figure 2.1 – Typical Suspended Mounting System

• The installer must make certain that the selected location will

permit adequate cooling and ventilating airflow.

Installation

Содержание quietpact 85d

















































































































Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды

Generac Power Systems quietpact 85d, Руководство пользователя

Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды