Generac Power Systems quietpact 85d Скачать руководство пользователя страница 4

Страница: 4 / 112

Study these SAFETY RULES carefully before installing, operating,

or servicing this equipment. Become familiar with this manual and

with the unit. The generator can operate safely, efficiently, and reli-

ably only if it is properly installed, operated, and maintained. Many

accidents are caused by failing to follow simple and fundamental

rules or precautions.
The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit, are, therefore, not all-inclusive.

If using a procedure, work method, or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method, or

operating technique utilized does not render the generator unsafe.



Despite the safe design of this generator,

operating this equipment imprudently,

neglecting its maintenance, or being care-

less can cause possible injury or death.

Permit only responsible and capable persons

to operate and maintain this equipment.



Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.



Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.

GENERAL HAZARDS

• For safety reasons, the manufacturer recommends that the

installation, initial startup, and maintenance of this equipment

be performed by an Authorized Service Dealer.

• The generator engine releases DEADLY carbon monoxide gas

through its exhaust system. This dangerous gas, if breathed

in sufficient concentrations, can cause unconsciousness or

even death. Never operate the generator set with the vehicle

inside any garage or other enclosed area. DO NOT OPERATE

THE GENERATOR IF THE EXHAUST SYSTEM IS LEAKING OR

HAS BEEN DAMAGED. SYMPTOMS OF CARBON MONOXIDE

POISONING ARE (a) inability to think coherently, (b) nausea,

(f) dizziness, (g) headaches, (h) weakness, and (i) sleepi-

ness. IF EXPERIENCING ANY OF THESE SYMPTOMS, MOVE

INTO FRESH AIR IMMEDIATELY. IF SYMPTOMS PERSIST, GET

MEDICAL HELP. Shut down the generator and do not operate it

until it has been inspected and repaired.

• Never sleep in the vehicle while the genset is running unless the

vehicle has a working carbon monoxide detector. The exhaust

system must be installed in accordance with the genset instal-

lation manual. Make sure there is ample fresh air when operat-

ing the genset in a confined area.

• The engine exhaust fumes contain carbon monoxide, which

can be DEADLY. This dangerous gas, if breathed in sufficient

concentrations, can cause unconsciousness or even death.

Thus, the exhaust system must be installed properly, in strict

compliance with applicable codes and standards. Following

installation, do nothing that might render the system unsafe or

in noncompliance with such codes and standards. The gen-

erator compartment must be completely vapor-sealed from the

vehicle interior. There must be no possibility of exhaust fumes

entering the vehicle interior. Never operate this equipment with

a leaking or defective exhaust system.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving or hot parts. Never remove any drive belt or

fan guard while the unit is operating.

• Adequate, unobstructed flow of cooling and ventilating air is

critical to correct generator operation and is required to expel

toxic fumes and fuel vapors from the generator compartment.

Without sufficient cooling airflow, the engine/generator quickly

overheats, which seriously damages the generator. Do not alter

the installation or permit even partial blockage of ventilation

provisions, as this can also seriously affect the safe operation

of the generator.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Inspect the generator regularly, and contact the nearest

Authorized Service Dealer immediately for parts needing repair

or replacement.

• Before performing any maintenance on the generator, discon-

nect its battery cables to prevent accidental startup. First,

disconnect the cable from the battery post, indicated by a

NEGATIVE, NEG, or (–). Reconnect this cable last.

• Never use the generator, or any of its parts, as a step. Stepping

on the unit can stress and break parts, resulting in dangerous

operating conditions due to leaking exhaust gases, fuel leakage,

oil leakage, etc.

• Never insert any tool or other object through openings in the

generator interior, even if the unit is not running. Serious injury

or damage to the equipment could be done.



SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe operation be

copied and posted in potential hazard areas of the recreational vehicle. Safety should be stressed to

all operators and potential operators of this equipment.

Safety Rules

Содержание quietpact 85d

















































































































Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды

Generac Power Systems quietpact 85d, Руководство пользователя

Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды