Generac Power Systems quietpact 85d Скачать руководство пользователя

Страница: 10 / 112

2.2

OPTIONAL REMOTE START/
STOP

This generator is equipped with a plug-in connector that can

be interfaced with an optional remote panel provided inside the

vehicle. This option allows for starting and stopping the generator

conveniently from within the vehicle. Refer to Part II - "Installation

Instructions", for details on the remote start/stop option.

2.3 BEFORE STARTING THE

ENGINE

NOTE:

Instructions and information in this manual assume the genera-

tor has been properly installed, connected, serviced, tested and

adjusted by a qualified installation technician or installation

contractor.

2.3.1 INSTALLATION

Generator installation must have been properly completed so that it

complies with all applicable codes, standards, and regulations and

with the manufacturer's recommendations.

NOTE:

Be sure the installation complies with all standards and codes

listed in the "Standards Booklets" section of this manual.

2.3.2 ENGINE

LUBRICATION

Before starting the engine, have the engine crankcase prop-

erly serviced with the recommended oil. Refer to the "Engine Oil

Requirements", "Checking the Engine Oil Level" and Changing the

Engine Oil and/or Filter" sections for oil servicing procedures and

recommendations.



Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine

failure.

2.3.3 FUEL

SUPPLY

The engine must have an adequate supply of proper fuel to oper-

ate. Before starting it, check that sufficient fuel is available.

NOTE:

Depending on the installation, the generator may have either

a separate fuel tank or “share” the vehicle’s engine fuel tank.
Some installations using a “shared” fuel tank may have a gen-

erator fuel pickup tube that is shorter than the vehicle’s engine

pickup tube. Such an arrangement causes the generator engine

to “run out of fuel”, while adequate fuel for the vehicle engine

remains in the tank.

2.3.4 COOLANT

LEVEL

Check the engine coolant level prior to initial use and at recom-

mended intervals. Refer to the “Coolant” and “Engine Coolant”

sections for procedures and recommendations.

2.3.5 COOLING AND VENTILATING AIR

Air inlet and outlet openings in the generator compartment

must be open and unobstructed for continued proper operation.

Without sufficient cooling and ventilating airflow, the engine/

generator may overheat, causing engine shutdown and damage

to the generator.

2.3.6 ENGINE EXHAUST GAS

Before starting the generator engine, be sure there is no way for

exhaust gases to enter the vehicle interior and endanger people or

animals. Close windows, doors, and other openings in the vehicle

that, if open, might permit exhaust gases to enter the vehicle.



The generator engine releases DEADLY

carbon monoxide gas through its exhaust

system. This dangerous gas, if breathed

in sufficient concentrations, can cause

unconsciousness or even death. NEVER

operate the generator set with the vehicle

inside any garage or other enclosed area.

DO NOT OPERATE THE GENERATOR IF THE

EXHAUST SYSTEM IS LEAKING OR HAS

BEEN DAMAGED. SYMPTOMS OF CARBON

MONOXIDE POISONING ARE (a) inability to

think coherently, (b) nausea, (c) vomiting, (d)

twitching muscles, (e) throbbing temples,

(f) dizziness, (g) headaches, (h) weakness,

and (i) sleepiness. IF EXPERIENCING ANY

OF THESE SYMPTOMS, MOVE INTO FRESH

AIR IMMEDIATELY. IF SYMPTOMS PERSIST,

GET MEDICAL HELP. Shut down the genera-

tor and do not operate it until it has been

inspected and repaired.



NEVER sleep in the vehicle while the genset

is running unless the vehicle has a working

carbon monoxide detector. The exhaust sys-

tem MUST be installed in accordance with

the genset installation manual. Make sure

there is ample fresh air when operating the

genset in a confined area.

Operation

Содержание quietpact 85d

















































































































Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды

Generac Power Systems quietpact 85d, Руководство пользователя

Результаты поиска

Содержание quietpact 85d

Отзывы:

Похожие инструкции для quietpact 85d

Бренды по названию

Популярные бренды