31
Figure 2.14 – Generator AC Output Leads
T2 Neutral (White)
T1 (Red)
T3 (Black)
T2 Neutral
(White)
Ground
(Green)
Generator Conversion to 120/240 Volt Dual Voltage
NOTE:
Conversion of this generator from "120 volts only, dual circuits"
to "120/240 volt - dual circuits" (or vice-versa) requires rerout-
ing wires within the unit enclosure. It is recommended that this
conversion be performed by an Authorized Service Dealer.
Figure 2.16 shows the stator power winding connections for
120/240 volt dual voltage. The stator power windings are con-
nected in series. Lead 11/11A connects to T1 (Red), lead 44/44A
connects to T3 (Black), while leads 22 and 33 are grounded and
connect to T2 NEUTRAL (White). A "tie bar" connects the two
switch handles on line breaker CB1.
To convert from "120 volt dual circuits" to "120/240 volt dual volt-
age", disconnect battery power from the generator and reverse
stator lead wires 33 and 44 as follows:
NOTE:
It is necessary to feed stator lead wires 33 and 44 through
grommets on the electrical enclosure and engine control box in
order to perform the rerouting outlined below. The front and top
unit enclosure panels, as well as the user control panel, must
be removed to perform this. After re-routing, wires should be
properly tied down to prevent chafing or contact with moving
internal components
1. Remove stator lead wire 44, as shown in Figure 2.15, from
the ground stud adjacent to the four-position terminal block.
Reroute stator lead 33 from the line side terminal of CB1A
(renamed as CB1 in Figure 2.16) to the ground stud location
previously occupied by stator lead wire 44.
2. Move smaller gauge (#18 AWG) wire labeled #11 (not
shown), from the top of CB1 to the top of CB1A. Renumber
this wire #44.
3. Reroute stator lead wire 44, removed in step 1, to the line
side terminal on CB1.
4. Renumber ground wire "44", located between the four-posi-
tion terminal block and ground in Figure 2.15, as ground wire
"33", as shown in Figure 2.16.
5. Renumber wire "33A" from Figure 2.15 as wire "44A" in
Figure 2.16.
6. Remove the 12 AWG jumper wire from between line breakers
CB1 and CB1A, as shown in Figure 2.15.
7. Install a "tie bar" between the two-line breaker switch handles.
DO NOT connect electrical loads in excess of
any circuit breaker rating, or problems will
develop with circuit breaker tripping, which
causes a loss of AC output. Also, DO NOT
exceed the generator's rated wattage capaci-
ty. Add the watts or amps of all lighting, appli-
ance, tool, and motor loads the generator will
operate at one time. This total should be less
than the unit's rated wattage/amperage capac-
ity.
Figure 2.15 – Connections for 120 Volts Only — Dual
Circuits
Figure 2.16 – Connections for 120/240 Dual Voltage
2.6.4 CONDUIT
Route the connections between the generator and the junction box
through approved, flexible conduit. The following general rules
apply:
• All wiring, conduit, and interconnections must be installed in
compliance with applicable codes, standards, and regulations.
• Cut wiring to the required length, and allow extra wire for junc-
tion box connections.
Installation
Содержание quietpact 85d
